382600

Skil 4465 Seite 5

5
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
INTRODUCTION
● This tool is intended for making cut-throughs and
cut-outs in wood, plastic, metal, ceramic plates and
rubber, and is suitable for straight and curved cuts with
mitre angles to 45°
TECHNICAL SPECIFICATIONS 1
SAFETY
● Read and save this instruction manual (pay special
attention to the safety instructions at the back)
● Always keep the cord away from moving parts of the tool
● If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
● Never use tool when cord is damaged; have it replaced
by a qualified person
● Do not cut material containing asbestos
● Do not use a saw blade which is cracked, deformed or
dull
● Keep hands away from the saw blade while the tool is in
use
● Remove all obstacles on top of as well as underneath
the cutting path before you start cutting
● Always disconnect plug from power source before
making any adjustment or changing any accessory
● Wear a dust protection mask when working with
materials which produce dust that is detrimental to
health; inform yourself beforehand about the materials to
be worked on
● Wear protective goggles when working with materials
which produce chips
● Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start cutting
● Check the functioning of the tool before each use and, in
case of a defect, have it repaired immediately by a
qualified person; never open the tool yourself
● Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
● When used outdours, connect the tool via a fault current
(FI) circuit breaker with a triggering current of 30 mA
maximum, and only use an extension cord which is
intended for outdour use and equipped with a
splashproof coupling-socket
● The noise level when working can exceed 85 dB(A);
wear ear protection
● When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
● SKIL can assure flawless functioning of the tool only
when original accessories are used
● Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
● In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
● This tool should not be used by people under the age of
16 years
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
● Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
● If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left
unattended
USE
● On/off
Switch on/off the tool by pulling/releasing trigger A 2
● Switch lock
- pull trigger A 2 and hold it while you press knob B 2
- release the trigger
- unlock the switch by pulling again trigger A and then
releasing it
● Speed control
Select speed with speed selection wheel C 2 (the
selfcorrecting VariTronic-Extra system keeps the speed
practically constant as the load increases)
● Recommended speed 3
● Vari-Orbit system
- use knob D 2 for adjusting the orbital action from
accurate cutting (=0) to fast cutting (=Full)
! Vari-Orbit system is activated when saw blade
enters into the workpiece
● Recommended orbital action 4
! when sawing splinter-sensitive material, use
lower orbital settings, or switch off orbital action,
to avoid splintering
● Auto-Scroller system
For 360° rotation of the saw blade around its axis, so
that intricate curves can be cut without turning the tool
(set knob D 2 in “auto-scroller” position)
- auto-scrolling 5
- manual scrolling (use knob E 2) 6
- 4 locked blade positions 7
! Vari-Orbit system only functions when saw blade
is locked for straight forward cutting
● Dust suction
Prevents large accumulations of dust, high dust
concentrations in the breathing air and facilitates the
disposal of saw dust
- mount vacuum cleaner adapter 8
- connect vacuum cleaner
- clean vacuum cleaner adapter regularly
! do not use vacuum cleaner when cutting metal
● Contact protector
Contact protector F 2 prevents unintentional contact
with the saw blade while working
● Changing blades 2
- loosen screw H in blade holder G
- insert blade to full depth with teeth facing forward
- tighten screw H firmly
GB
5
XP SKIL 4465 28-05-2002 12:45 Pagina 5
… 5 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Skil 4465 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info