Bedienungsanleitung Skil 4581 AA (Seite 10 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

110184

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

c) Disconnect the plug from the power source before

making any adjustments, changing accessories, or

storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

SAFETY INSTRUCTIONS FOR JIG SAWS

• Always keep the cord away from moving parts of the

tool; direct the cord to the rear, away from the tool

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use tool when cord is damaged; have it replaced

by a qualiﬁ ed person

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Take protective measures when during work dust

can develop that is harmful to one’s health,

combustible or explosive (some dusts are considered

carcinogenic); wear a dust mask and work with dust/

chip extraction when connectable

• Do not use a saw blade which is cracked, deformed or

dull

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Keep hands away from the saw blade while the tool is in

use

• Remove all obstacles on top of as well as underneath

the cutting path before you start cutting

• Always disconnect plug from power source before

making any adjustment or changing any accessory

• Wear protective goggles when working with materials

which produce chips

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Check the functioning of the tool before each use and,

in case of a defect, have it repaired immediately by a

qualiﬁ ed person; never open the tool yourself

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools

with a rating of 230V or 240V can also be connected to

a 220V supply)

• When used outdoors, connect the tool via a fault current

(FI) circuit breaker with a triggering current of 30 mA

maximum, and only use an extension cord which is

intended for outdoor use and equipped with a

splashproof coupling-socket

• The noise level when working can exceed 85 dB(A);

wear ear protection

• When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

• SKIL can assure ﬂ awless functioning of the tool only

when original accessories are used

• Use completely unrolled and safe extension cords with

a capacity of 16 Amps (U.K. 13 Amps)

• In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

• This tool should not be used by people under the age of

16 years

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left unattended

USE

• On/off 4

• Speed control for smooth starting 5 (4585)

• Switch locking for continuous use 6

• Changing saw blades 7

! insert blade to full depth with teeth facing

forward 8

• Sawing at 45° 9

• Adjusting sawing speed to material used 0

! if the tool does not run with wheel E in position 1,

select a higher sawing speed and lower the

sawing speed while the tool runs

• Selecting sawing mode !

Use lever F 2 for adjusting the orbital action from

accurate cutting (=0) to fast cutting (=4)

- 1 setting (“0”) for accurate cutting in all materials,

straight + curved

- 4 settings for fast cutting in different materials,

straight cuts only

1 = metal

2 = plastic

3 = hard wood

4 = soft wood

! always select “0” when sawing splinter-sensitive

material

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 4581 AA Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info