Bedienungsanleitung Skil 5003 aa (Seite 10 von 144) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

383642

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

• Adjusting cutting depth (0-66 mm) 4

- for an optimal quality cut the saw blade should not

extend more than 3 mm below the workpiece

- loosen lever J

- raise/lower foot K until desired cutting depth is set on

scale using indicator L

- tighten lever J

• Adjusting cutting angle (0-45°) 5

- loosen knob M

- tilt tool until desired cutting angle is set on scale

using indicator N

- tighten knob M

! when bevel cutting, cutting depth does not

correspond with value on cutting depth scale

• 90° Cutting angle check 5

- adjust and tighten foot K to maximum cutting depth 4

- adjust and tighten cutting angle to 0°

- check for 90° angle between the blade and bottom of

foot with a square

- if adjustment is needed, tilt and tighten foot to 45°

and bend tab P with an adjustable wrench

• Line-of-cut indicator Q 6

- for guiding tool along desired line of cut marked on

the workpiece

- for a straight 0° cut or a 45° bevel cut use the

indicator line concerned

- allows you to choose whether waste material is on

inner or outer side of blade

! the wide part of the foot should rest on the

supported part of the workpiece

! cutting width is determined by width of blade

teeth and not bywidth of blade body

! always make trial cuts first to verify actual line of

cut

• Dust suction

- connect vacuum cleaner to extension R 7

! never let the vacuum cleaner hose interfere with

the lower guard or the cutting operation

- one may also use a dust bag (SKIL accessory

2610387402)

• Operating the tool 7

- connect plug to power source

- always hold handle S ﬁ rmly with one hand and

handle T ﬁ rmly with the other hand

- place tool with front end of foot ﬂ at on workpiece

! ensure that the saw teeth are not engaged into

the workpiece

- switch on tool by ﬁ rst pressing knob U (= safety

switch which cannot be locked) and then pulling

trigger V

! the tool should run at full speed before the blade

enters into the workpiece

- lower guard F opens automatically when saw blade

enters the workpiece (open lower guard manually by

using lever G only for special cuts such as plunge

cuts)

- do not force the tool; apply light and continuous

pressure

! while working, always hold the tool at the grey-

coloured grip area(s)

- after completing the cut switch off tool by releasing

trigger V

! ensure that the blade has come to a complete

standstill, before you lift the tool from the

workpiece

APPLICATION ADVICE

• Always face the good side of the workpiece down to

ensure minimum splintering

• Only use sharp saw blades of the correct type 8

- quality of cut improves by the number of teeth

- carbide tipped blades stay sharp up to 30 times

longer than ordinary blades

• Rip fence W 9

- for making exact cuts along a workpiece edge

- can be inserted in either side of foot

Adjusting rip fence

- loosen knob X

- adjust to desired cutting width by using rip fence

scale (use line-of-cut indicator Q as 0-reference)

- tighten knob X

• Plunge cutting 0

- set desired cutting depth

- tilt tool forward with line-of-cut indicator Q lined up

with desired line of cut marked on the workpiece

- open lower guard F with lever G

- just before blade enters workpiece, switch on tool

and gradually lower back end of tool using front end

of foot as hinge-point

- gradually move tool downward as well as forward

- as soon as blade enters the material, release lever G

! never pull tool backwards

• Cutting large panels !

- support panel close to the cut either on ﬂ oor, table or

workbench

! set cutting depth so that you cut through panel

and not through support

- in case rip fence does not allow desired width of cut,

clamp or nail straight piece of wood to workpiece as

a guide, and use the right side of the foot against this

guide

• Vibration level

The vibration emission level stated at the back of this

instruction manual has been measured in accordance

with a standardised test given in EN 60745; it may be

used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories, may

signiﬁ cantly increase the exposure level

- the times when the tool is switched off or when it is

running but not actually doing the job, may

signiﬁ cantly reduce the exposure level

! protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 5003 aa Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info