Bedienungsanleitung Skil 5064 AA (Seite 11 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

482541

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

• Line-of-cut indicator P 6

- for guiding tool along desired line of cut marked on

the workpiece

- for a straight 0° cut or a 45° bevel cut use the indicator

line concerned

! the wide part of the foot should rest on the

supported part of the workpiece

! cutting width is determined by width of blade

teeth and not by width of blade body

! always make trial cuts first to verify actual line

of cut

• Dust suction

- connect vacuum cleaner to extension Q 7

! never let the vacuum cleaner hose interfere with

the lower guard or the cutting operation

- one may also use a dust bag (SKIL

accessory 2610387402)

! do not use dustbag/vacuum cleaner when

cutting metal

• Operating the tool 7

- connect plug to power source

- always hold handle R rmly with one hand and handle

S rmly with the other hand

- place tool with front end of foot at on workpiece

! ensure that the saw teeth are not engaged into

the workpiece

- switch on tool by rst pressing knob T (= safety switch

which cannot be locked) and then pulling trigger V

! the tool should run at full speed before the blade

enters into the workpiece

- lower guard F opens automatically when saw blade

enters the workpiece (open lower guard manually by

using lever G only for special cuts such as

plunge cuts)

! do not force the tool (apply light and continuous

pressure in order to avoid overheating the blade tips

and, in case of cutting plastics, melting the

plastic material)

! while working, always hold the tool at the

grey-coloured grip area(s)

- after completing the cut switch o tool by releasing

trigger V

! ensure that the blade has come to a complete

standstill, before you lift the tool from

the workpiece

APPLICATION ADVICE

• Always face the good side of the workpiece down to

ensure minimum splintering

• Only use sharp saw blades of the correct type 8

- quality of cut improves by the number of teeth

- carbide tipped blades stay sharp up to 30 times longer

than ordinary blades

• Rip fence W 9

- for making exact cuts along a workpiece edge

- can be inserted in either side of foot

Adjusting rip fence

- loosen knob X

- adjust to desired cutting width by using rip fence scale

(use line-of-cut indicator P as 0-reference)

- tighten knob X

• Plunge cutting 0

- set desired cutting depth

- tilt tool forward with line-of-cut indicator P lined up with

desired line of cut marked on the workpiece

- open lower guard F with lever G

- just before blade enters workpiece, switch on tool and

gradually lower back end of tool using front end of foot

as hinge-point

- gradually move tool downward as well as forward

- as soon as blade enters the material, release lever G

! never pull tool backwards

• Cutting large panels !

- support panel close to the cut either on oor, table

or workbench

! set cutting depth so that you cut through panel

and not through support

- in case rip fence does not allow desired width of cut,

clamp or nail straight piece of wood to workpiece as a

guide, and use the right side of the foot against

this guide

MAINTENANCE / SERVICE

• Always keep tool and cord clean (especially the

ventilation slots)

! disconnect the plug before cleaning

• Always keep the area around lower guard F 3 clean

(remove dust and chips by blowing out with compressed

air or with a brush)

• Clean saw blade immediately after use (especially from

resin and glue)

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skileurope.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol @ will remind you of this when the need for

disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that this product

is in conformity with the following standards or

standardized documents: EN 60745, EN 61000,

EN 55014, in accordance with the provisions of the

directives 2004/108/EC, 2006/42/EC

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 5064 AA Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info