Bedienungsanleitung Skil 5740 aa (Seite 9 von 49) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

383479

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

Circular saw 5140/5740

INTRODUCTION

● This tool is intended for lengthways and crossways

cutting of wood with straight cuts as well as angle cuts to

45°; with the appropriate saw blades also non-ferrous

metals, light building materials and plastics can be cut

TECHNICAL SPECIFICATIONS 1

SAFETY

● Read and save this instruction manual and the

enclosed safety instructions

● Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start cutting

● Always keep the cord away from moving parts of the tool

● When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

● Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

● In case of jamming or electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

● SKIL can assure flawless functioning of the tool only

when original accessories are used

● Before using accessories always compare the maximum

allowed speed of that specific accessory with the speed

of the tool

● Never use the tool without the original protection guard

system

● This tool should not be used by people under the age of

16 years

● The noise level when working can exceed 85 dB(A);

wear ear protection

● If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

● Never use tool when cord is damaged; have it replaced

by a qualified person

● Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

● This tool is not suitable for wet cutting

● The kerf guide has to be adjusted in case different

diameters of sawblade are used

● Do not use a circular saw blade which is cracked,

deformed or dull

● Do not use a circular saw blade of which the body

thickness is bigger, or the teeth setting is smaller than

the thickness of the kerf guide

● After switching off your circular saw, never stop the rotation

of the saw blade by a lateral force applied against it

● Never clamp or wedge the lower guard in open position;

ensure that it operates freely

● Never use circular saw blades made of high speed steel

(HSS)

● Never use grinding/cutting discs with this tool

● Do not remove the kerf guide

● Keep hands away from the saw blade while the tool

is in use

● Do not cut material containing asbestos

● Do not attempt to cut extremely small workpieces

● Remove all obstacles on top of as well as underneath

the cutting path before you start cutting

● Do not work overhead with the tool

● Only use a saw table provided with a switch that prevents

restarting of the motor after interruption of voltage

● Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left unattended

USE

● Changing saw blade 3

- open lower guard A by using lever B

- change saw blade with saw teeth and arrow printed

on saw blade pointing in same direction as arrow on

lower guard A

! make sure that clamping surfaces C of flanges are

perfectly clean and face the blade

- tighten blade bolt D with hex key 1/8 turn past finger

tight (ensures slippage of saw blade when it

encounters excessive resistance thus reducing motor

overload and saw kickback)

● Adjusting cutting depth (0-40 mm) 4

- for an optimal quality cut the saw blade should not

extend more than 3 mm below the workpiece

- loosen knob E

- raise/lower foot F until desired cutting depth is set on

scale using indicator G

- tighten knob E

● Adjusting cutting angle (0-45°) 5

- loosen knob H

- tilt tool until desired cutting angle is set on scale using

indicator J

- tighten knob H

! when bevel cutting, cutting depth does not

correspond with value on cutting depth scale

● 90° Cutting angle check 5

- adjust and tighten foot F to maximum cutting depth 4

- adjust and tighten cutting angle to 0°

- check for 90° angle between the blade and bottom of

foot with a square

- if adjustment is needed, tilt and tighten foot to 45° and

bend tab K with an adjustable wrench

● Kerf guide L 6

- protects saw blade from getting jammed in the workpiece

- needs readjustment when min./max. distance is

affected or upon changing of saw blade

Readjusting kerf guide 6

- adjust and tighten foot F to maximum cutting depth 4

- loosen bolt M

- adjust kerfguide L

- tighten bolt M

● Line-of-cut indicator N 7a (5140)

Adjustable saw line visor N 7b (5740)

XP SKIL 5140/5740 19-03-2003 12:20 Pagina 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 5740 aa Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Skil 5740 aa

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info