Bedienungsanleitung Skil 6224 (Seite 7 von 100) (Alle Sprachen)

591183

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR DRILL/DRIVERS

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• SKIL can assure awless functioning of the tool only

when original accessories are used

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

• This tool should not be used by people under the age of

16 years

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Always keep the cord away from moving parts of the tool

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• If the drill bit becomes unexpectedly jammed (causing a

sudden, dangerous reaction), immediately switch o the

tool

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Hold the power tool only by the insulated gripping

surfaces when performing an operation where the

accessory may contact hidden wiring or its own

power cord (contact with a “live” wire will also make

exposed metal parts of the power tool “live” and shock

the operator)

• Use suitable detectors to find hidden utility lines or

call the local utility company for assistance (contact

with electric lines can lead to re or electrical shock;

damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• Alwaysdisconnectplugfrompowersourcebefore

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• On/O 4

• Speed control for smooth starting 5

• Changing direction of rotation 6

- when not properly set in left/right position, switch A 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits 7

- insert the bit as deep as possible in the chuck

! do not use bits with a damaged shank

• Torque control (VariTorque) 8

- output torque will increase as clutch ring D is rotated

from 1 to 20; position E will lock up the clutch to permit

drilling or driving heavy duty work

- when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

• Mechanical gear selection 9

- set selector F to desired speed

! actuate the gear selector while tool is running

slowly

LOW

- low speed

- high torque

- for screwdriving and drilling large diameters

- for tapping thread

HIGH

- high speed

- lower torque

- for drilling small diameters

• Holding and guiding the tool 0

! while working, always hold the tool at the

grey-coloured grip area(s)

- keep ventilation slots G 2 uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits !

! only use sharp bits

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 6224 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info