Bedienungsanleitung Skil 6460 (Seite 6 von 45) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

387683

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

INTRODUCTION

● This tool is intended for hammer drilling in brick,

concrete and stone as well as for drilling in wood, metal,

ceramic and plastic; tools with electronic speed control

and left/right rotation are also suitable for screwdriving

and thread cutting

TECHNICAL SPECIFICATIONS 1

OPERATING CONTROLS 234

A Switch for on/off and speed control

B Button for switch locking

C Wheel for maximum speed control

D Switch for changing direction of rotation

E Switch for selecting drilling function

F Wheel for maximum speed control/torque control

G Switch for selecting drilling/screwdriving position

H Spindle-lock button

SAFETY

● Read and save this instruction manual (pay special

attention to the safety instructions at the back)

● Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

● Always keep the cord away from moving parts of the tool

● When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

● Use completely unrolled and safe extension cords with a

capacity of 16 Amps (UK 13 Amps)

● In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

● SKIL can assure flawless functioning of the tool only

when original accessories are used

● Before using accessories always compare the maximum

allowed r.p.m. of that specific accessory with the r.p.m.

of the tool

● This tool should not be used by people under the age of

16 years

● Be careful not to drill or drive into areas where electrical

wires may be contacted

● The noise level when working can exceed 85 dB(A);

wear ear protection

● If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

● Never use tool when cord is damaged; have it replaced

by a qualified person

● Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

● If the drill bit becomes unexpectedly jammed (causing a

sudden, dangerous reaction), immediately switch off the

tool

● Be aware of the forces that occur as a result of jamming

(especially when drilling metals); always hold the tool

firmly with both hands and take a secure stance

● Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left

unattended

USE

● On/Off 5

● Switch locking for continuous use 6

● Speed control for smooth starting 7

● Maximum speed control

With wheel C/F the maximum speed can be adjusted

from low to high (1-5)

6460/6463/6464 23

- switch on the tool

- lock the switch

- turn wheel C to select maximum speed

6466 4

- set switch G in drilling position

- switch on the tool

- turn wheel F to select maximum speed

● Torque control (6466) 4

With wheel F the amount of torque delivered by the

chuck can be adjusted steplessly from minimum to

maximum (1-5)

- set switch G in screwdriving position (maximum

speed is adjusted automatically)

- switch on the tool

- turn wheel F to select torque

- to prevent overtightening of screws, always start with

low torque and adjust accordingly

When torque has reached its adjusted value, the rotation

of the chuck will stop; if subsequently load is removed

from the tool while the on/off switch is still activitated,

the tool continues to run at very low speed for safety

reasons; release switch A briefly to resume operation

● Changing direction of rotation 8

- when not properly set in left/right position, switch A

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

● Normal drilling/screwdriving versus hammer drilling 9

! select drilling function only when tool is switched

off

● Changing bits 0!@

- insert the bit as deep as possible in the chuck

! do not use bits with a damaged shank

! push spindle-lock button only when tool is at a

complete standstill @

● Adjusting drilling depth #

● Holding and guiding the tool $

- keep the ventilation slots uncovered

- do not apply too much pressure on the tool; let the

tool do the work for you

XP SKIL 6460/6463/6464/6466 12-06-2002 16:29 Pagina 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 6460 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info