Bedienungsanleitung Skil 6475 (Seite 7 von 40) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

387661

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

INTRODUCTION

● This tool is intended for hammer drilling in concrete,

brick and stone as well as for drilling in wood, metal,

ceramic and plastic; tools with electronic speed control

and left/right rotation are also suitable for screwdriving

and thread cutting

TECHNICAL SPECIFICATIONS 1

OPERATING CONTROLS 2

A Switch for on/off and speed control

B Button for switch locking

C Wheel for maximum speed control

D Switch for changing direction of rotation

E Switch for selecting mechanical speed

F Switch for selecting drilling function

G Auxiliary handle

SAFETY

● Read and save this instruction manual (pay special

attention to the safety instructions at the back)

● Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

● Always keep the cord away from moving parts of the tool

● When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

● Use completely unrolled and safe extension cords with a

capacity of 16 Amps (UK 13 Amps)

● In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

● SKIL can assure flawless functioning of the tool only

when original accessories are used

● Before using accessories always compare the maximum

allowed r.p.m. of that specific accessory with the r.p.m.

of the tool

● This tool should not be used by people under the age of

16 years

● Be careful not to drill or drive into areas where

electrical wires may be contacted; always use

auxiliary handle G2

● The noise level when working can exceed 85 dB(A);

wear ear protection

● If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

● Never use tool when cord is damaged; have it replaced

by a qualified person

● Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

● If the drill bit becomes unexpectedly jammed (causing a

sudden, dangerous reaction), immediately switch off the

tool

● Be aware of the forces that occur as a result of jamming

(especially when drilling metals); always use auxiliary

handle G2 and take a secure stance

● Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left unattended

USE

● On/Off 3

● Switch locking for continuous use 4

● Speed control for smooth starting 5

● Maximum speed control 6a

● 2 Mechanical speeds 6b

! change speed only when tool is switched off

1 = LOW SPEED

- high torque

- for screwdriving and drilling large diameters

- for tapping thread

2 = HIGH SPEED

- lower torque

- for drilling small diameters

● For determining the optimal speed table 6c can be

used as reference

● Changing direction of rotation 7

- when not properly set in left/right position, switch A

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

● Normal drilling/screwdriving versus hammer drilling 8

! select drilling function only when tool is switched

off

● Changing bits 9

- insert the bit as deep as possible in the chuck

! do not use bits with a damaged shank

● Adjusting drilling depth 0

● Holding and guiding the tool !

! always use auxiliary handle G2

- keep the ventilation slots uncovered

- do not apply too much pressure on the tool; let the

tool do the work for you

APPLICATION ADVICE

● Use the appropriate bits @

! only use sharp bits

● When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

● When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

of the wood

● Splinterfree drilling in wood #

● Dustfree drilling in walls $

● Dustfree drilling in ceilings %

● Drilling in tiles without skidding ^

● For more tips see www.skileurope.com

GUARANTEE / ENVIRONMENT

● Always keep tool and cord clean (especially the

ventilation slots)

! disconnect the plug before cleaning

XP SKIL 6470/6475 27-03-2003 14:21 Pagina 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 6475 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info