Bedienungsanleitung Skil 7240 (Seite 4 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

389825

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

INTRODUCTION

● This tool is intended for dry sanding and finishing of

wood, painted surfaces, plastic and filler

TECHNICAL SPECIFICATIONS 1

SAFETY

● Read and save this instruction manual (pay special

attention to the safety instructions at the back)

● Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

● Always keep the cord away from moving parts of the tool

● When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

● Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

● In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

● We recommend to use original SKIL-accessories as

listed at the back of this instruction manual

● This tool should not be used by people under the age of

16 years

● The noise level when working can exceed 85 dB(A);

wear ear protection

● If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

● Never use tool when cord is damaged; have it replaced

by a qualified person

● Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

● This tool is not suitable for wet sanding

● Do not sand material containing asbestos

● When sanding metal, sparks are generated; do not use

dustbag and keep other persons and combustible

material from work area

● Do not touch the moving sanding sheet

● Do not continue to use worn, torn or heavily clogged

sanding sheets

● Wear protective gloves, safety glasses, close-fitting

clothes and hair protection (for long hair)

● Wear a dust protection mask when working with

materials which produce dust that is detrimental to

health; inform yourself beforehand about the materials to

be worked on

● Always direct the cord to the rear away from the tool

● Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left

unattended

USE

● Mounting of sanding sheet

! disconnect the plug

! the dust suction requires the use of perforated

sanding sheets

! perforation in sanding sheet should correspond

with perforation in sanding foot 2

! replace worn sanding sheets in time

! always use the tool with the total sanding surface

covered with sanding paper

WHEN USING TOOL AS AN ORBITAL SANDER 3

- remove delta tip A while pushing button B

- mount rectangle C by inserting tabs in holes at a 45˚

angle and pushing it towards housing until it

snap-locks

- mount VELCRO sanding sheet as illustrated (do not

remove part 2)

WHEN USING TOOL AS A DELTA SANDER 4

- remove rectangle C while pushing button B

- mount delta tip A by inserting tabs in holes at a 45˚

angle and pushing it towards housing until it

snap-locks

- mount VELCRO sanding sheet as illustrated (remove

part 2 and keep it for using tool as an orbital sander)

● Dust suction 5

- mount dust bag

- empty dustbag regularly for optimal dust pick-up

performance

! do not use dustbag when sanding metal

● On/off switch

- switch on/off the tool by pushing switch D 5

forward/backwards

! before the sanding surface reaches the

workpiece, you should switch on the tool

! before switching off the tool, you should lift it

from the workpiece

● Holding and guiding the tool 6

- guide the tool parallel to the working surface

! do not apply too much pressure on the tool; let

the sanding surface do the work for you

- do not tilt the tool in order to avoid unwanted sanding

marks

- keep the ventilation slots uncovered

APPLICATION ADVICE

● Use the tool as an orbital sander for large working

surfaces (wooden table-tops, floors, doors, stairsteps, etc.)

7 8 9

● Use the tool as a delta-sander for edged, narrow and

other hard-to-reach places on your workpiece

(window-frames, staircases, furniture, etc.) 8 9

● When the foampad of the delta-tip is worn or damaged

at the top, you may extend its service life twice by

tearing it off, turning it 120˚ and putting it back

(also applicable to delta sanding sheet) 0

● Never use the same sanding sheet for wood and metal

XP SKIL 7210.2 31-03-2004 12:23 Pagina 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 7240 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info