Bedienungsanleitung Skil 7330 (Seite 4 von 40) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

389478

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

INTRODUCTION

● This tool is intended for dry sanding and finishing of

wood, painted surfaces, plastic and filler

TECHNICAL SPECIFICATIONS 1

SAFETY

● Read and save this instruction manual (pay special

attention to the safety instructions at the back)

● Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

● Always keep the cord away from moving parts of the tool

● When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

● Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

● In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

● SKIL can assure flawless functioning of the tool only

when original accessories are used

● This tool should not be used by people under the age of

16 years

● The noise level when working can exceed 85 dB(A);

wear ear protection

● If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

● Never use tool when cord is damaged; have it replaced

by a qualified person

● Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

● This tool is not suitable for wet sanding

● Do not sand material containing asbestos

● When sanding metal, sparks are generated; do not use

dustbag/vacuum cleaner and keep other persons and

combustible material from work area

● Do not touch the moving sanding sheet

● Do not continue to use worn, torn or heavily clogged

sanding sheets

● Wear protective gloves, safety glasses, close-fitting

clothes and hair protection (for long hair)

● Wear a dust protection mask when working with

materials which produce dust that is detrimental to

health; inform yourself beforehand about the materials to

be worked on

● Always direct the cord to the rear away from the tool

● Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left

unattended

USE

● Mounting of sanding sheet

7310/7320 2a

7330/7340/7345 2a+b

! the dust suction requires the use of perforated

sanding sheets

- perforation in sanding sheet should correspond with

perforation in sanding foot

! replace worn sanding sheets in time

● Dust suction

7310 3

- when using tool with/without vacuum cleaner, mount

vacuum cleaner adaptor A as illustrated

! do not use vacuum cleaner when sanding metal

7320/7330/7340/7345 4

- mount dust bag

- empty dustbag regularly for optimal dust pick-up

performance

! do not use dustbag when sanding metal

● On/off switch

- switch on/off the tool by pushing switch B 3 forward/

backwards

! before the sanding surface reaches the

workpiece, you should switch on the tool

! before switching off the tool, you should lift it

from the workpiece

● VariTronic speed control (7340/7345)

For optimal sanding results on different materials

- with wheel C 4 you can set the desired sanding

speed

- adjust speed to grit size used (see: Application

Advice)

- before starting a job, find the optimal speed and grit

by testing out on spare material

● Holding and guiding the tool 5

- guide the tool parallel to the working surface

! do not apply pressure on the tool; let the sanding

surface do the work for you

- do not tilt the tool in order to avoid unwanted sanding

marks

-keep the ventilation slots uncovered

APPLICATION ADVICE

● Move the tool in straight movements in line with the

grain

- for sanding bare wood surfaces

- for extra fine finishing

● Never use the same sanding sheet for wood and metal

● Recommended sanding sheet grits:

coarse - for removing paint;

for sanding of extremely rough wood

medium - for sanding of rough or plain wood

fine - for smoothing of wood;

for finishing of bare wood;

for smoothing surfaces with old paint

● Use different grit sizes when the working surface is

rough:

- start sanding with coarse or medium grit

- finish with fine grit

● For more tips see www.skileurope.com

SKIL7310/20/30/40/45.qxd 05-02-2004 09:56 Pagina 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 7330 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info