Bedienungsanleitung Skil 7381 (Seite 7 von 96) (Alle Sprachen)

644764

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR SANDERS

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• When you put away the tool, switch o the motor and ensure

that all moving parts have come to a complete standstill

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• SKIL can assure awless functioning of the tool only

when the correct accessories are used which can be

obtained from your SKIL dealer

• This tool should not be used by people under the age of

16 years

• The noise level when working can exceed 85 dB(A);

wear ear protection

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• This tool is not suitable for wet sanding

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• When sanding metal, sparks are generated; do not use

dustbag and keep other persons and combustible

material from work area

• Do not touch the moving sanding sheet

• Do not continue to use worn, torn or heavily clogged

sanding sheets

• Wear protective gloves, safety glasses, close-tting

clothes and hair protection (for long hair)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Mounting of sanding sheet 4

! disconnect the plug

- mount VELCRO sanding sheet as illustrated

- use lever A for mounting regular sanding sheets

! the dust suction requires the use of perforated

sanding sheets

- use paper punch B for adapting non-perforated

sanding sheets to dust suction

! perforation in sanding sheet should correspond

with perforation in sanding foot

! replace worn sanding sheets in time

! always use the tool with the total sanding surface

covered with sanding paper

• Dust suction 5

- empty dustbox C regularly for optimal dust pick-up

performance

- remove dustbox C by pushing knob D to the left and hold

it in that position while pulling dustbox C backwards

- mount dustbox C by sliding it back until it clicks into place

! lock dustbox C before mounting

- when necessary, also clean the lter as illustrated

! do not use dustbox when sanding metal

• Mounting/removing of vacuum cleaner adapter E 6

! do not use vacuum cleaner when sanding metal

• On/o switch

- switch on/o the tool by pushing switch F 2

forward/backwards

! before the sanding surface reaches the

workpiece, you should switch on the tool

! before switching off the tool, you should lift it

from the workpiece

• Speed control

For optimal sanding results on dierent materials

- with wheel G 2 you can set the desired sanding speed

- adjust speed to grit size used

- before starting a job, nd the optimal speed and grit by

testing out on spare material

• Holding and guiding the tool 7

! while working, always hold the tool at the

grey-coloured grip area(s)

- guide the tool parallel to the working surface

! do not apply too much pressure on the tool; let

the sanding surface do the work for you

- do not tilt the tool in order to avoid unwanted

sanding marks

- keep ventilation slots H 2 uncovered

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 7381 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info