Bedienungsanleitung Skil 7445 (Seite 6 von 104) (Alle Sprachen)

591197

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

 Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

 When sanding metal, sparks are generated; do not

use dust box and keep other persons and combustible

material from work area

DURING USE

 Always keep the cord away from moving parts of the

tool; direct the cord to the rear, away from the tool

 Do not touch the moving sanding disc

 In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

 If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

AFTER USE

 When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

 Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

 If for any reason the old plug is cut o the cord of

this tool, it must be disposed of safely and not left

unattended

USE

 Backing pads

- never run the tool without backing pad A

! replace damaged backing pads immediately

(loosen/fasten 4 pad screws B)

! unplug tool before removing/mounting backing

pads

 Mounting of sanding sheet

- mount VELCRO sanding sheet C as illustrated

- if necessary, clean backing pad rst

! perforation in sanding sheet should correspond

with perforation in sanding foot

! the dust suction requires the use of perforated

sanding sheets

! replace worn sanding sheets in time

 Dust suction

- empty dust box D regularly for optimal dust pick-up

performance

For using vacuum cleaner

- remove dust box D by pushing knob E to the left

and hold it in that position while pulling dust box D

backwards

- connect vacuum cleaner to extension F

! do not use dust box/vacuum cleaner when

sanding metal

 Dust level indicator

- empty dust box D when indicator G turns RED

- indicator G only functions when tool is switched on

- be aware that the working of the dust level indicator is

not guaranteed when sanding at lower speed settings

(7455)

 On/o switch

- switch on/o the tool by pushing switch H

forward/

backwards

! before the sanding surface reaches the

workpiece, you should switch on the tool

! be aware of the sudden impact when the tool is

switched on

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any



operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

dierent from those intended could result in a hazardous

situation.

5) SERVICE

a) 

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

SAFETY INSTRUCTIONS FOR SANDERS

GENERAL

 This tool should not be used by people under the age

of 16 years

 This tool is not suitable for wet sanding

 Never use the tool when cord is damaged; have it

replaced by a qualied person

 Do not work materials containing asbestos

(asbestos is considered carcinogenic)

 Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

 SKIL can assure awless functioning of the tool only

when original accessories are used

 Do not continue to use worn, torn or heavily clogged

sanding discs

BEFORE USE

 Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

 Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

 Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

 The noise level when working can exceed 85 dB(A);

wear ear protection

 Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

 Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

 Follow the dust-related national requirements for the

materials you want to work with

 Wear protective gloves, safety glasses, close-tting

clothes and hair protection (for long hair)

Skil 7445 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info