Bedienungsanleitung Skil 7460 aa (Seite 7 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

390161

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR SANDERS

GENERAL

• This tool should not be used by people under the age of

16 years

• This tool is not suitable for wet sanding

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when original accessories are used

• Do not continue to use worn, torn or heavily clogged

sanding discs

BEFORE USE

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• The noise level when working can exceed 85 dB(A); wear

ear protection

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Wear protective gloves, safety glasses, close-tting

clothes and hair protection (for long hair)

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• When sanding metal, sparks are generated; do not use

dustbox and keep other persons and combustible

material from work area

DURING USE

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Do not touch the moving sanding disc

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

AFTER USE

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Backing pads

- never run the tool without backing pad A

! replace damaged backing pads immediately

(loosen/fasten 4 pad screws B)

! unplug tool before removing/mounting backing

pads

• Mounting sanding discs

- simply press sanding disc C onto backing pad with

perforation in sanding disc corresponding with

perforation in backing pad

- if necessary, clean backing pad rst

! the dust suction requires the use of perforated

sanding discs

• Dust suction 4

- empty dustbox D regularly for optimal dust pick-up

performance

- remove dustbox D by pushing knob J to the left and

hold it in that position while pulling dustbox D

backwards

- mount dustbox D by sliding it back until it clicks into

place

! do not use dustbox when sanding metal

• Pressure control 5 (7450/7460)

Warns the user when applying too much pressure on the

tool while working (too much pressure reduces the

sanding performance)

- green light 1 turns on in case of pressure

- green light 2/3 turns on in case of increased pressure

- red light 4 turns on when pressure is too high

NOTES:

! the pressure control feature only starts working

properly after the tool has run for approximately

one minute

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 7460 aa Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info