Bedienungsanleitung Skil 7520 MA (Seite 12 von 176) (Alle Sprachen)

644679

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of

this tool, it must be disposed of safely and not left

unattended

USE

• Assembly instructions ⑦

- unfold the tool and ensure that screw A ts the slot in

the tool handle connection

- push down lever B completely for locking the handle

connection

! if necessary, use hex key C for loosening/

tightening screw A when handle connection

cannot be locked completely

- for folding the tool handle vice-versa

• Extending tool to medium length (165 cm) ⑧

- loosen locking sleeve D by turning it in the direction of

the unlocking symbol on the tool

- extend the tool to the desired length (123 - 165 cm)

- tighten locking sleeve D by turning it in the direction of

the locking symbol on the tool

• Extending tool to maximum length (220 cm) ⑨

- loosen locking sleeve E by turning it in the direction of

the unlocking symbol on the tool handle

- insert additional handle F into the end of the tool

handle until the marking as illustrated aligns with the

edge of locking sleeve E

- tighten locking sleeve E by turning it in the direction of

the locking symbol on the tool handle

! extending the tool to its maximum length is only

possible when tool is already extended to its

medium length

• Backing pads ⑩

- never run the tool without backing pad G

! replace damaged backing pads immediately

(loosen/fasten pad screw H with hex key C)

! unplug tool before removing/mounting backing

pads

• Mounting sanding discs ⑪

- simply press sanding disc J onto backing pad with

perforation in sanding disc corresponding with

perforation in backing pad

- if necessary, clean backing pad rst

! the dust suction requires the use of perforated

sanding discs

• Dust suction ⑫

- loosen locking sleeve E by turning it in the direction of

the unlocking symbol on the tool handle

- insert exible hose K into the end of the tool handle as

illustrated

- tighten locking sleeve E by turning it in the direction of

the locking symbol on the tool handle

- connect the exible hose with the Ø 57 mm adapter

directly to an industrial vacuum cleaner (remove

)

- one may also connect exible hose K with one of the

3 adapters to an industrial vacuum cleaner without

removing the vacuum cleaner hose

- for mounting vacuum cleaner adapter L or M use

screwdriver N as illustrated

• Tool standard/airow control ⑬

- tool standard P prevents the hose from damage when

putting the tool aside during work breaks

- control the airow by sliding regulator Q over the

opening in tool connector R

- the vacuuming power is at its lowest level when the

opening is fully visible

• On/o locking switch S ⑭

- switch on tool ⑭a

! before the accessory reaches the workpiece, the

tool should run at full speed

- lock switch ⑭b

- unlock switch/switch o tool ⑭c

! 

from the workpiece

! the accessory continues to rotate for a short time



• Electronic soft-start

Ensures reaching the maximum speed smoothly without

a sudden impact when tool is switched on

• Electronic constant speed

Keeps the speed at a constant level as the load

increases

• Speed control ⑮

For optimal sanding results on dierent materials

- with wheel T you can adjust the sanding speed

steplessly from minimum to maximum

- always adjust speed to grit size used

- before starting a job, nd the optimal speed and grit by

testing out on spare material

• Holding and guiding the tool ⑯

! 

! 

coloured grip area(s)

- guide the tool parallel to the working surface and move

it in circles or in a cross pattern

! do not apply too much pressure on the tool; let

the sanding surface do the work for you

- do not tilt the tool in order to avoid unwanted sanding

marks

- keep ventilation slots V ② uncovered

• Sanding

- the amount of material removed is determined by the

speed of the sanding disc and the grit size used

- the speed of the sanding disc decreases relative to the

pressure applied to the tool

APPLICATION ADVICE

• Use the tool at extended length for sanding (higher)

walls ⑰

• Use the tool at maximum length for sanding ceilings ⑱

• For sanding hard-to-reach places pad cover segment W

can be removed as illustrated ⑲

MAINTENANCE / SERVICE

• Replace a damaged sanding hose X ② as illustrated ⑳

• A damaged power cord shall be replaced at a SKIL

service centre only in order to avoid a hazard

• Store the tool in its protective case in a dry and locked-

up place, out of reach of children ㉑

• Always keep tool and cord clean (especially ventilation

slots V ②)

! do not attempt to clean ventilation slots by

Skil 7520 MA Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info