Bedienungsanleitung Skil 7720 (Seite 6 von 108) (Alle Sprachen)

644817

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR SCRAPERS

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• When used outdoors, connect the tool via a fault current

(FI) circuit breaker with a triggering current of 30 mA

maximum, and only use an extension cord which is

intended for outdoor use and equipped with a

splashproof coupling-socket

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Pay attention to the risk of injury caused by material

particles that splinter o and y about; wear safety

glasses and protective gloves

• Never place your hands in front of the immediate working

area

• Keep other persons out of the working area while working

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Do not work with moistened materials (such as

wallpaper) or in damp areas

• Do not soak the work area with solvents (while scraping,

poisonous vapours could be produced as a result of the

warming up of the worked material)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Hold the power tool only by the insulated gripping

surfaces when performing an operation where the

accessory may contact hidden wiring or its own

power cord (contact with a “live” wire will also make

exposed metal parts of the power tool “live” and shock

the operator)

• Use suitable detectors to find hidden utility lines or

call the local utility company for assistance (contact

with electric lines can lead to re or electrical shock;

damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when connectable

• Follow the dust-related national requirements for the

materials you want to work with

• This tool should not be used by people under the age of

16 years

• SKIL can assure awless functioning of the tool only

when the correct accessories are used which can be

obtained from your SKIL dealer

• Alwaysdisconnectplugfrompowersourcebefore

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Mounting of accessories 4

! wear protective gloves

- slide switch C backward to unlock accessory holder E

- slide the accessory (with the working edge pointing

downward) to full depth into accessory holder E

- slide switch C forward to lock accessory holder E

- clean the accessory shaft after each replacement

• On/o

- switch on the tool by pushing switch A 3 forward

- switch o the tool by pushing switch A 3 backwards

(position 0)

• Speed control 5

- select working speed by sliding switch A into desired

position

1 = low speed for precision work

2 = medium speed

3 = high speed for quick removal of material

- the optimal working speed depends on the material

and can be determined with practical trials

• Operating the tool

! wear protective gloves and use safety glasses

- mount desired accessory

- switch on the tool

- advance the tool to the material/location to be scraped

- start with a at angle and light pressure

- work away from the body

- be aware that the stroke motion of the tool is only

produced when pressure is applied to the material to

be removed

- be aware that too much pressure may cause damage

to the background material

! do not overload the tool

! allow tool and accessory to cool down between

the individual work steps

Skil 7720 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info