Bedienungsanleitung Skil 8004 (Seite 7 von 156) (Alle Sprachen)

591209

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR HEAT GUNS

BEFORE USE:

• Check the functioning of the tool before each use and, in

case of a defect, have it repaired immediately by a

qualied person; never open the tool yourself

• Inspect tool cord and plug before each use and, if

damaged, have them replaced by a qualied person

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Inspect the extension cord periodically and replace it, if

damaged

• Use the tool and its accessories in accordance with this

instruction manual and in the manner intended for the

tool; use of the tool for operations, dierent from those

normally expected to be performed by the tool, could

result in a hazardous situation

• This tool should not be used by people under the age of

16 years

• This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction

concerning use of the tool by a person responsible for

their safety

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Be sure tool is switched o when plugging in

DURING USE:

• Handlethetoolwithcare;preventfireandburns

- do not touch the air outlet/nozzle and the heated

object; they become extremely hot

- do not hold the air outlet/nozzle too close to the object

to be worked on

- do not direct the hot air ow towards the same surface

for too long

- never look down the air outlet/nozzle

- wear protective gloves and use safety glasses

- never direct the hot air ow towards persons or

animals

- never use the tool for drying hair

- do not leave the tool unattended

- never use the tool in the proximity of inammable

gases or combustible materials (risk of explosion)

- when working with plastic, paint, varnish and similar

materials, inammable and poisonous gases may be

produced; inform yourself beforehand about the

materials to be worked on

- take into account, that heat may be transferred to

combustible materials out of eyesight

- to be on the safe side, have a bucket of water or a re

extinguisher handy, in case any material catches re

• Preventelectricalshock

- never poke anything down the air outlet/nozzle

- avoid body contact with earthed surfaces (e.g. pipes,

radiators, ranges, refrigerators)

- ensure the tool does not get wet

- do not use the tool in damp locations

- when used outdoors, connect the tool via a fault

current (FI) circuit breaker with a triggering current of

30 mA maximum, and only use an extension cord

which is intended for outdoor use and equipped with a

splashproof coupling-socket

• Handlethecordwithcare

- always keep away the cord from the hot air ow and

the air outlet/nozzle

- keep the cord away from heat, oil and sharp edges

- do not carry the tool by the cord, and do not yank the

cord to disconnect it from the socket

- do not suspend the tool by the cord

• Never use the tool in conjunction with chemical solvents

• Make sure work area is adequately ventilated

• Keep work area clean and well lit

• Keep children away from work area

• Ensure that children do not play with the tool

• Inrush currents cause short-time voltage drops; under

unfavourable power supply conditions, other equipment

may be aected (if the system impedance of the power

supply is lower than 0,127 + j0,079 Ohm, disturbances

are unlikely to occur); if you need further clarication, you

may contact your local power supply authority

• Stay alert; watch what you are doing, use common sense

and do not operate the tool when you are tired

• Take a secure stance; do not overreach, especially on

ladders and stages

• Ensure that the tool is switched o, before putting it aside

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

AFTER USE:

• Switch o the tool and disconnect the plug

• Allowthetooltocooldownforatleast30minutes

before storage

• Suspend the tool on hanging ring M 2 or set it down on

its rear in an upright position; when doing so, make sure

no combustible materials or inammable gases are in the

proximity

• Do not store/leave the tool outdoors

• Store the tool in a dry and locked-up place, out of reach

of children

Skil 8004 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info