Bedienungsanleitung Skil 8020 (Seite 9 von 124) (Alle Sprachen)

758004

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

OTHER APPLICATION EXAMPLE:

shrink-wrapping

• Soldering water pipes o

This tool is most suitable for working with soft solders

(melting point below 400°)

-use reector nozzle J

-thoroughly clean both joining sections before soldering

-pre-heat both sections and apply soldering wire (do

not use lead-based soldering wire)

• Thawing out frozen water pipes p

-use reector nozzle J

-heat the frozen area evenly

! 

from gas pipes; heating gas pipes is extremely

dangerous – risk of explosion

OTHER APPLICATION EXAMPLES:

thawing out water pipes made of PVC (position II,

max. 60°C)

thawing out frozen car locks (position II, max. 60°C)

(use reduction nozzle )

defrosting freezers (do not damage the plastic

housing)

thawing out ice-covered steps and pavements

• Shaping plastic tubes

-use reector nozzle J

-ll the tube with sand and seal it at both ends, to avoid

kinking of the tube

-heat the tube evenly by moving it from side to side

OTHER APPLICATION EXAMPLES:

shaping all plastics with a low melting-point

(polyethylene, PVC etc.)

shaping all plastics with a high melting-point (acrylic

glass, Plexiglas etc.)

shaping and bending carpet tiles made of synthetic

bres

shaping and bending of wood (model-building)

• Welding plastics

-the weld seam must be clean and grease-free

-keep welding rod close to weld seam and apply heat,

until the welding rod gets tacky

-remove heat, when weld seam is lled up

OTHER APPLICATION EXAMPLES:

repairing of surfboards, skis and other synthetic sports

goods (use round nozzle H)

welding PVC-materials

smoothing blisters after sticking PVC-labels

connecting garden hoses (use reector nozzle J)

• Drying

! only dry with a low or medium temperature setting

(position I or II) and with an increased distance

between the tool and the workpiece

-drying of paint, varnish, gypsum, mortar and plaster

-drying wet timber prior to lling

-drying thickly applied ller or adhesive quickly

-drying building joints before spraying insulation or

sealant

-drying joints and cracks in boatbuilding

• Cleaning/disinfecting

-disinfecting rabbit hutches, dove cotes, etc. (remove

)

-combatting ant colonies

-combatting woodworms and boring beetles (hold the

tool at an adequate distance from the wood)

-eliminating weeds

APPLICATION ADVICE

• Removing paint/lacquer r

-use a clean, sharp scraper

-scrape rmly, when the paint softens

-experiment to establish the length of time necessary to

apply the heat for optimal results

-scrape the softened paint immediately, or it will harden

again

-keep a 30° to 40° angle between the tool and the

workpiece

-remove paint and debris immediately from the scraper

to prevent them from ignition

-scrape with the grain of the wood, wherever possible

-do not direct the hot air ow towards the same surface

for too long

-dispose of all paint debris safely

-thoroughly clean the work area after completing the job

! be careful when removing layers of paint in old

buildings; in the past the building may have been

painted with paint containing lead, which is highly

poisonous

! exposure to even low levels of lead can cause

serious brain and nervous system damage; young

and unborn children are particularly vulnerable

! have lead-based paint removed by a professional

without using a heat gun

OTHER APPLICATION EXAMPLE:

removing (synthetic) wall covering

• Removing paint/lacquer next to glass t

-always use glass protection nozzle G when working

next to glass

-remove the paint with a hand scraper

! do not use the tool for removing paint on metal-

framed windows; metal is heat-conducting which

might lead to breaking of the glass

• Removing stickers (use round nozzle H) y

-many adhesives become softer when heated, allowing

adhesive bonds to be separated and superuous

adhesive to be removed

! heat sticker on the upper side

! always take care not to overheat the underlying

surface

OTHER APPLICATION EXAMPLES:

removing linoleum and vinyl carpeting

removing carpet tiles made of synthetic bres

removing veneers/applying veneer strips

softening/melting tar, tin, bitumen, wax (use round

nozzle H)

waxing (skis, furniture) (use glass protection nozzle

G) u

removing resin

loosening rusty/too tightly fastened metal screws, nuts

and bolts

removing candle wax (do not overheat the

underlying surface)

repairing broken candles/restoring bent candles to their

original shape

• Shrink tting i

-use reector nozzle J or reduction nozzle K

-select a shrink-t tube with a diameter matching that of

the workpiece

-heat the shrink-t tube evenly

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 8020 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info