Bedienungsanleitung Skil 8200AA (Seite 7 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

482530

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Power tools are dangerous in the hands of untrained

users.

e) Maintainpowertools.Checkformisalignmentor

bindingofmovingparts,breakageofpartsandany

otherconditionthatmayaffectthepowertool’s

operation.Ifdamaged,havethepowertoolrepaired

beforeuse. Many accidents are caused by poorly

maintained power tools.

f) Keepcuttingtoolssharpandclean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Usethepowertool,accessoriesandtoolbitsetc.,in

accordancewiththeseinstructions,takinginto

accounttheworkingconditionsandtheworktobe

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5)SERVICE

a) Haveyourpowertoolservicedbyaqualifiedrepair

personusingonlyidenticalreplacementparts. This

will ensure that the safety of the power tool is maintained.

SAFETYINSTRUCTIONSFORTACKERS

• Alwaysassumethatthetoolcontainsfasteners

(careless handling of the tacker can result in unexpected

ring of fasteners and personal injury)

• Donotpointthetooltowardsyourselforanyone

nearby (unexpected triggering will discharge the fastener

causing an injury)

• Donotactuatethetoolunlessthetoolisplaced

firmlyagainsttheworkpiece (if the tool is not in

contact with the workpiece, the fastener may be deected

away from your target)

• Disconnectthetoolfromthepowersourcewhenthe

fastenerjamsinthetool (while removing a jammed

fastener, the tacker may be accidentally activated if it is

plugged in)

• Usecautionwhileremovingajammedfastener (the

mechanism may be under compression and the fastener

may be forcefully discharged while attempting to free a

jammed condition)

• Donotusethistackerforfasteningelectricalcables

(it is not designed for electric cable installation and may

damage the insulation of electric cables thereby causing

electric shock or re hazards)

• Securetheworkpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction

concerning use of the tool by a person responsible for

their safety

• Ensure that children do not play with the tool

• SKIL can assure awless functioning of the tool only

when original accessories are used

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

EXPLANATIONOFSYMBOLSONTOOL

3 Read the instruction manual before use

4 Double insulation (no earth wire required)

5 Do not dispose of the tool together with household waste

material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Loading staples/nails 6

! disconnecttheplug

- turn tool upside down

- press lever A while pulling slider B backwards

- insert the staple/nail strip into magazine C with legs

facing upward (maximal capacity 100 staples/80 nails)

- push slider B against tacker head D until it snap-locks

- when inserting a nail strip (not supplied with the tool)

tilt the tool in such a way, that the nail strip rests

against the magazine side which corresponds with the

nail symbol on tacker head D 7

- reload magazine C when end of staple- or nail strip

shows in opening H 2

• Operating the tool 8

- switch on the tool by pushing switch E in “I” position

- rmly press tacker head D against the workpiece until

it is pushed in completely

- briey press switch F and then release again

! whileworking,alwaysholdthetoolatthe

grey-colouredgriparea(s)

- switch o the tool by pushing switch E in “O” position

• Impact control 9

With wheel G the required impact level can be adjusted

steplessly from minimum to maximum (- / +)

- “-” for thin and light materials such as foils and fabrics

- “+” for thick and tough materials such as hard woods

and walls

- before starting a job, nd the optimal impact level by

testing out on spare material

APPLICATIONADVICE

• Fastening panels 0

• Fixing textiles !

• For stapling hard wood use shorter staples than the ones

supplied with the tool

• Avoid blank shots in order to reduce the wear of the

impact strike

• For more tips see skileurope.com

Skil 8200AA Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info