Bedienungsanleitung Skil 9006 (Seite 11 von 168) (Alle Sprachen)

701673

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Mounting of accessories

! disconnect the plug

- clean spindle A and all parts to be mounted

- tighten clamping ange B with spanner C while pushing

spindle-lock button D

! 

at a standstill

- for removing accessories handle vice-versa

! grinding/cutting discs become very hot during

use; do not touch them until they have cooled

down

! never use a grinding/cutting disc without the label

(“blotter”) which is glued onto it (if provided)

• Mounting of auxiliary handle E

! disconnect the plug

- screw auxiliary handle E on the right, the top, or the left

of the tool (depending on the work to be carried out)

• Removing/mounting/adjusting of protective guard F

! disconnect the plug

- open protective guard F by loosening screw G (do not

remove it)

- place protective guard F on the spindle collar of the tool

head and turn it to the required position (depending on

the work to be carried out)

! ensure that the closed side of the protective guard

always points to the operator

- fasten protective guard F by tightening screw G

! 

• Before using the tool

- ensure that accessory is correctly mounted and rmly

tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 60 seconds at highest no-load

speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

• On/o locking switch K

- switch on tool

! be aware of the sudden impact when the tool is

switched on

! before the accessory reaches the workpiece, the

tool should run at full speed

- lock switch

- unlock switch/switch o tool

! 

the workpiece

! the accessory continues to rotate for a short time



• Grinding

- move the tool back and forth with moderate pressure

! never use a cutting disc for side grinding

• Cutting

- do not tilt the tool while cutting

- always move the tool in same direction as arrow on tool

head, in order to prevent the tool from being pushed out

of the cut in an uncontrolled manner

OUTDOOR USE

• Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

BEFORE USE

• Before using the tool for the rst time, it is recommended

to receive practical information

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Always mount auxiliary handle E

and protective guard

; never use the tool without them

• 

or call the local utility company for assistance

(contact with electric lines can lead to re or electrical

shock; damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Be careful when cutting grooves, especially in supporting

walls (slots in supporting walls are subject to country-

specic regulations; these regulations are to be observed

under all circumstances)

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Do not clamp the tool in a vice

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

DURING USE

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when the cord is damaged; it must be

replaced by a specially prepared cord available through

an after-sales service centre for SKIL power tools and

carried out by a qualied person

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• In case of current interruption or when the plug

is accidentally pulled out, the tool will not restart



switch

c and switch on tool again

AFTER USE

• After switching o the tool, never stop the rotation of the

accessory by a lateral force applied against it

EXPLANATION OF SYMBOLS ON TOOL

Read the instruction manual before use

Wear protective glasses and hearing protection

Double insulation (no earth wire required)

Do not dispose of the tool together with household waste

material

Skil 9006 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info