Bedienungsanleitung Skil 9134 (Seite 11 von 172) (Alle Sprachen)

758603

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

! 

at a standstill

-for removing accessories handle vice-versa

! grinding/cutting discs become very hot during

use; do not touch them until they have cooled



! 



• Mounting of auxiliary handle F 7

! disconnect the plug

-screw auxiliary handle F on the right, the top, or the left

of the tool (depending on the work to be carried out)

• Removing/mounting/adjusting of protective guard G 8

! disconnect the plug

! ensure that the closed side of the protective guard



-if necessary, adjust protective guard G by tightening

screw X which is pre-set at manufacturing (ensure that

the protective guard is closed)

• Before using the tool

-ensure that accessory is correctly mounted and rmly

tightened

-check if accessory runs freely by turning it by hand

-test-run tool for at least 60 seconds at highest no-load

speed in a safe position

-stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

• On/o safety switch H 9

-switch on tool 9a

! 



! 

tool should run at full speed

-switch o tool 9b

! 



! the accessory continues to rotate for a short time



• Grinding q

-move the tool back and forth with moderate pressure

! never use a cutting disc for side grinding

• Cutting w

-do not tilt the tool while cutting

-always move the tool in same direction as arrow on tool

head, in order to prevent the tool from being pushed out

of the cut in an uncontrolled manner

-do not apply pressure on the tool; let the speed of the

cutting disc do the work

-the working speed of the cutting disc depends on the

material to be cut

-do not brake cutting discs with side pressure

• Holding and guiding the tool e

-always hold the tool rmly with both hands, so you will

have full control of the tool at all times

! 

coloured grip area(s) e

-provide for a secure stance

-pay attention to the direction of rotation; always hold the

tool so, that sparks and grinding/cutting dust y away

from the body

-keep ventilation slots J 2 uncovered

• Mounting/removing spanner C r

-only applicable if tool is executed with auxiliary handle

with integrated spanner storage

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Always mount auxiliary handle F 2 and protective guard

F 2; never use the tool without them

• 

or call the local utility company for assistance

(contact with electric lines can lead to re or electrical

shock; damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

•  (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); 



• Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; 



connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Be careful when cutting grooves, especially in supporting

walls (slots in supporting walls are subject to country-

specic regulations; these regulations are to be observed

under all circumstances)

•  (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Do not clamp the tool in a vice

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

DURING USE

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when the cord is damaged; it must be

replaced by a specially prepared cord available through

the service organization.

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

AFTER USE

• After switching o the tool, never stop the rotation of the

accessory by a lateral force applied against it

EXPLANATION OF SYMBOLS ON TOOL

3 Read the instruction manual before use

4 Wear protective glasses and hearing protection

5 Double insulation (no earth wire required)

6 Do not dispose of the tool together with household waste

material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

•If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Mounting of accessories 2

! disconnect the plug

-clean spindle A and all parts to be mounted

-tighten clamping ange B with spanner C while pushing

spindle-lock button D

Skil 9134 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info