Bedienungsanleitung Skil 9235 (Seite 8 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

391287

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

BEFORE USE

• Before using the tool for the ﬁ rst time, it is

recommended to receive practical information

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools

with a rating of 230V or 240V can also be connected to

a 220V supply)

• Always mount auxiliary handle A 2 and protective

guard B 2; never use the tool without them

• Use suitable detectors to find hidden utility lines or

call the local utility company for assistance (contact

with electric lines can lead to ﬁ re or electrical shock;

damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause

allergic reactions and/or respiratory diseases to the

operator or bystanders); wear a dust mask and work

with a dust extraction device when connectable

• Certain kinds of dust are classiﬁ ed as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Be careful when cutting grooves, especially in

supporting walls (slots in supporting walls are subject to

country-speciﬁ c regulations; these regulations are to be

observed under all circumstances)

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Do not clamp the tool in a vice

• Use completely unrolled and safe extension cords with

a capacity of 16 Amps (U.K. 13 Amps)

DURING USE

• Inrush currents cause short-time voltage drops; under

unfavourable power supply conditions, other equipment

may be affected (if the system impedance of the power

supply is lower than 0,25 Ohm, disturbances are

unlikely to occur); if you need further clariﬁ cation, you

may contact your local power supply authority

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualiﬁ ed person

• In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

• In case of current interruption or when the plug is

accidentally pulled out, unlock the on/off switch H 2

immediately and put it in the OFF-position in order to

prevent uncontrolled restarting

AFTER USE

• After switching off the tool, never stop the rotation of

the accessory by a lateral force applied against it

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left

unattended

USE

• Mounting of accessories 2

! disconnect the plug

- clean spindle C and all parts to be mounted

- tighten clamping ﬂ ange E with spanner F while

pushing spindle-lock button G

! push spindle-lock button G only when spindle C is

at a standstill

- for removing accessories handle vice-versa

! grinding/cutting discs become very hot during

use; do not touch them until they have cooled

down

! never use a grinding/cutting disc without the label

(“blotter”) which is glued onto it

• Mounting of auxiliary handle A 5

• Adjusting protective guard B 6

! disconnect the plug

! ensure that the closed side of the protective

guard always points to the operator

• Before using the tool

- ensure that accessory is correctly mounted and ﬁ rmly

tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 30 seconds at highest no-

load speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

• On/off locking switch H 7

- switch on tool 7a

! be aware of the sudden impact when the tool is

switched on

! before the accessory reaches the workpiece, the

tool should run at full speed

- lock switch 7b

- unlock switch/switch off tool 7c

! before switching off the tool, you should lift it

from the workpiece

! the accessory continues to rotate for a short time

after the tool has been switched off

• Grinding 8

- move the tool back and forth with moderate pressure

! never use a cutting disc for side grinding

• Cutting 9

- do not tilt the tool while cutting

- always move the tool in same direction as arrow on

tool head, in order to prevent the tool from being

pushed out of the cut in an uncontrolled manner

- do not apply pressure on the tool; let the speed of

the cutting disc do the work

- do not brake cutting discs with side pressure

• Holding and guiding the tool

! while working, always hold the tool at the grey-

coloured grip area(s) 0

- always hold the tool ﬁ rmly with both hands, so you

will have full control of the tool at all times

Skil 9235 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info