Bedienungsanleitung Skil 9375 (Seite 5 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

390794

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

INTRODUCTION

● This tool is intended for grinding, cutting and deburring

metal and stone materials without the use of water; with

the appropriate accessories the tool can also be used for

brushing and sanding

TECHNICAL SPECIFICATIONS 1

SAFETY

GENERAL

● Read and save this instruction manual and the

enclosed safety instructions 2

● Only use this tool for dry grinding/cutting

● Only use the flanges which are supplied with this tool

● This tool should not be used by people under the age of

16 years

● Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

● Use the original SKIL accessories which can be obtained

from your SKIL dealer

● For mounting/using non-SKIL accessories observe the

instructions of the manufacturer concerned

● Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

● Do not use damaged, deformed or vibrating grinding/

cutting discs

● Handle and store grinding/cutting discs carefully to avoid

chipping and cracking

● Protect accessories from impact, shock and grease

● Do not use a grinding/cutting disc that is larger than the

maximum recommended size

● Only use grinding/cutting discs with a hole diameter

which fits mounting flange D 6 without play; never use

reducors or adaptors to fit large-hole grinding/cutting

discs

● Never use grinding/cutting discs with a threaded hole, of

which the thread is not long enough to accept the spindle

length of the tool

● Never use accessories with a "blind" threaded hole

smaller than M14 x 21 mm

OUTDOOR USE

● Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

● Only use an extension cord which is intended for outdour

use and equipped with a splashproof coupling-socket

BEFORE USE

● Before using the tool for the first time, it is recommended

to receive practical information

● Do not work with materials containing asbestos

● Be careful of hidden electrical wires or gas- and water

pipes; check the work area, for instance with a metal

detector

● Be careful when cutting groves, especially in supporting

walls (slots in supporting walls are subject to country-

specific regulations; these regulations are to be observed

under all circumstances, so before beginning work,

consult with the responsible structural engineer, architect

or construction supervisor)

● Clamp the workpiece in case it does not remain

stationary from its own weight

● Do not clamp the tool in a vice

● Use completely unrolled and safe extension cords with a

capacity of 16 Amps (UK 13 Amps)

● Wear protective glasses and gloves, hearing protection

3, a dust mask, and sturdy shoes; when necessary, also

wear an apron

● Always mount auxiliary handle A 6 and protective guard

B 6; never use the tool without them

● Be sure tool is switched off when plugging in

DURING USE

● Always keep the cord away from moving parts of the

tool; direct the cord to the rear, away from the tool

● If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug;

never use the tool with a damaged cord

● Push spindle-lock button G 6 only when spindle C 6 is

at a standstill

● Keep hands away from rotating accessories

● When grinding metal, sparks are generated; keep other

persons and combustible material from work area

● In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

● In case the cutting disc is blocked, resulting in jerking

forces on the tool, immediately switch off the tool

● In case of current interruption or when the plug is

accidentally pulled out, unlock the on/off switch

immediately and put it in the OFF-position in order to

prevent uncontrolled restarting

● Do not apply so much pressure on the tool that it comes

to a standstill

AFTER USE

● Before you put down the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

● After switching off the tool, never stop the rotation of the

accessory by a lateral force applied against it

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left unattended

USE

● Mount auxiliary handle A 4

● Mount protective guard B 5

! ensure that the closed side of the protective guard

always points to the operator

XP SKIL 9370/9375/9380/9385.2 17-06-2003 10:36 Pagina 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 9375 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info