Bedienungsanleitung Skil 9390 (Seite 8 von 176) (Alle Sprachen)

591208

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

 Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

 If for any reason the old plug is cut o the cord of

this tool, it must be disposed of safely and not left

unattended

USE

 Mounting of accessories

! disconnect the plug

- clean spindle A and all parts to be mounted

- tighten clamping ange B with spanner C while

pushing spindle-lock button D

! 

is at a standstill

- for removing accessories handle vice-versa

! grinding/cutting discs become very hot during

use; do not touch them until they have cooled

down

! always mount backing pad when using sanding

accessories

! never use a grinding/cutting disc without



provided)

 Mounting of auxiliary handle E

! disconnect the plug

- screw auxiliary handle E on the right or the left of the

tool (depending on the work to be carried out)

 Adjusting of protective guard F

! disconnect the plug

! ensure that the closed side of the protective

guard always points to the operator

 Removing of protective guard F

! disconnect the plug

- for mounting protective guard, handle in reverse order

 Before using the tool

- ensure that accessory is correctly mounted and rmly

tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 30 seconds at highest no-load

speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

 On/o locking switch H

- switch on tool

! be aware of the sudden impact when the tool is

switched on

! before the accessory reaches the workpiece, the

tool should run at full speed

- lock switch

- unlock switch/switch o tool

! 

from the workpiece

! the accessory continues to rotate for a short time



 Grinding

- move the tool back and forth with moderate pressure

! never use a cutting disc for side grinding

 Cutting

- do not tilt the tool while cutting

- always move the tool in same direction as arrow on

tool head, in order to prevent the tool from being

pushed out of the cut in an uncontrolled manner

ACCESSORIES

 SKIL can assure awless functioning of the tool only

when original accessories are used

 Use only grinding/cutting discs with a maximum

thickness of 8 mm and a spindle hole diameter of

22 mm

 For mounting/using non-SKIL accessories observe the

instructions of the manufacturer concerned

 Never use reducors or adaptors to t large-hole

grinding/cutting discs

 Never use accessories with a "blind" threaded hole

smaller than M14 x 21 mm

OUTDOOR USE

 Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

BEFORE USE

 Before using the tool for the rst time, it is recommended

to receive practical information

 Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

 Always mount auxiliary handle E

and protective

guard F

; never use the tool without them

 

or call the local utility company for assistance

(contact with electric lines can lead to re or electrical

shock; damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

 Do not work materials containing asbestos

(asbestos is considered carcinogenic)

 Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

 Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

 Follow the dust-related national requirements for the

materials you want to work with

 Be careful when cutting grooves, especially in

supporting walls (slots in supporting walls are subject to

country-specic regulations; these regulations are to be

observed under all circumstances)

 Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

 Do not clamp the tool in a vice

 Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

DURING USE

 If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

 Never use the tool when cord is damaged; have it

replaced by a qualied person

 In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

 In case of current interruption or when the plug is

accidentally pulled out, immediately switch o the tool in

order to prevent uncontrolled restarting

AFTER USE

 After switching o the tool, never stop the rotation of the

accessory by a lateral force applied against it

Skil 9390 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info