Bedienungsanleitung Skil 9408 (Seite 7 von 164) (Alle Sprachen)

644814

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

duringstart-up.The operator can control torque

reactions or kickback forces, if proper precautions are

taken.

b) Neverplaceyourhandneartherotatingaccessory.

The accessory may kickback over your hand.

c) Donotpositionyourbodyintheareawherepower

toolwillmoveifkickbackoccurs.Kickback will propel

the tool in the direction opposite to the wheel’s movement

at the point of snagging.

d) Usespecialcarewhenworkingcorners,sharp

edgesetc.Avoidbouncingandsnaggingthe

accessory.Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control or kickback.

e) Donotattachasawchainwoodcarvingbladeor

toothedsawblade.Such blades create frequent

kickback and loss of control.

3)SAFETYWARNINGSSPECIFICFORGRINDINGAND

ABRASIVECUTTING-OFFOPERATIONS

a) Useonlywheeltypesthatarerecommendedfor

yourpowertoolandthespecificguarddesignedfor

theselectedwheel.Wheels for which the power tool

was not designed cannot be adequately guarded and are

unsafe.

b) Thegrindingsurfaceofthecentredepressed

wheelsmustbemountedbelowtheplaneofthe

guardlip. An improperly mounted wheel that projects

through the plane of the guard lip cannot be adequately

protected.

c) Theguardmustbesecurelyattachedtothepower

toolandpositionedformaximumsafety,sotheleast

amountofwheelisexposedtowardstheoperator.

The guard helps to protect the operator from broken

wheel fragments, accidental contact with wheel and

sparks that could ignite clothing.

d) Wheelsmustbeusedonlyforrecommended

applications.For example: Do not grind with the side of

a cut-o wheel. Abrasive cut-o wheels are intended for

peripheral grinding; side forces applied to these wheels

may cause them to shatter.

e) Alwaysuseundamagedwheelflangesthatareof

correctsizeandshapeforyourselectedwheel.

Proper wheel anges support the wheel thus reducing

the possibility of wheel breakage. Flanges for cut-o

wheels may be dierent from grinding wheel anges.

f) Donotuseworndownwheelsfromlargerpower

tools.A wheel intended for a larger power tool is not

suitable for the higher speed of a smaller tool and may

burst.

4)ADDITIONALSAFETYWARNINGSSPECIFICFOR

CUttING OFF OPERAtIONS

a) Donot“jam”thecut-offwheelorapplyexcessive

pressure.Donotattempttomakeanexcessive

depthofcut.Overstressing the wheel increases the

loading and susceptibility to twisting or binding of the

wheel in the cut and the possibility of kickback or wheel

breakage.

b) Donotpositionyourbodyinlinewithandbehind

therotatingwheel.When the wheel, at the point of

operation, is moving away from your body, the possible

kickback may propel the spinning wheel and the power

tool directly at you.

c) Whenthewheelisbindingorwheninterruptingacut

foranyreason,switchoffthepowertoolandholdthe

powertoolmotionlessuntilthewheelcomestoa

completestop.Neverattempttoremovethecut-off

wheelfromthecutwhilethewheelisinmotion,

otherwisekickbackmayoccur.Investigate and take

corrective action to eliminate the cause of wheel binding.

d) Donotrestartthecuttingoperationinthe

workpiece.Letthewheelreachfullspeedand

carefullyre-enterthecut.The wheel may bind, walk up

or kickback if the power tool is restarted in the workpiece.

e) Supportpanelsoranyoversizedworkpieceto

minimizetheriskofwheelpinchingandkickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

f) Useextracautionwhenmakinga“pocketcut”into

existingwallsorotherblindareas.The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

GENERAL

• Only use the anges which are supplied with this tool

• This tool should not be used by people under the age of

16 years

• This tool is not suitable for wet grinding/cutting

• Alwaysdisconnectplugfrompowersourcebefore

makinganyadjustmentorchanginganyaccessory

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when the correct accessories are used which can be

obtained from your SKIL dealer

• For mounting/using non-SKIL accessories observe the

instructions of the manufacturer concerned

• Useonlygrinding/cuttingdiscswithamaximum

thicknessof8mmandaspindleholediameterof22

• Never use reducors or adaptors to t large-hole grinding/

cutting discs

• Never use accessories with a “blind” threaded hole

smaller than M14 x 21 mm

OUtDOOR USE

• Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

BEFORE USE

• Before using the tool for the rst time, it is recommended

to receive practical information

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Always mount auxiliary handle E 2 and protective guard

F 2; never use the tool without them

• Usesuitabledetectorstofindhiddenutilitylinesor

callthelocalutilitycompanyforassistance (contact

with electric lines can lead to re or electrical shock;

damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Donotworkmaterialscontainingasbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

Skil 9408 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info