Bedienungsanleitung Skil 9412 (Seite 9 von 178) (Alle Sprachen)

644813

Zoom out

Zoom in

Vorherige Seite

1/178

Nächste Seite

 If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

 Never use the tool when cord is damaged; have it

replaced by a qualied person

 In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

 In case of current interruption or when the plug is

accidentally pulled out, release switch G

in order to

prevent uncontrolled restarting

AFTER USE

 After switching o the tool, never stop the rotation of the

accessory by a lateral force applied against it

EXPLANATION OF SYMBOLS ON TOOL

Read the instruction manual before use

Wear protective glasses and hearing protection

Double insulation (no earth wire required)

Do not dispose of the tool together with household

waste material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

 Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

 If for any reason the old plug is cut o the cord of

this tool, it must be disposed of safely and not left

unattended

USE

 Mounting of accessories

! disconnect the plug

- clean spindle A and all parts to be mounted

- tighten clamping ange B with spanner C while

pushing spindle-lock button D

! push spindle-lock button D only when spindle A

is at a standstill

- for removing accessories handle vice-versa

! grinding/cutting discs become very hot during

use; do not touch them until they have cooled

down

! always mount backing pad when using sanding

accessories

! never use a grinding/cutting disc without



provided)

 Mounting of auxiliary handle E

! disconnect the plug

- screw auxiliary handle E on the right, the top, or the

left of the tool (depending on the work to be carried

out)

 Adjusting of protective guard F

! disconnect the plug

! ensure that the closed side of the protective

guard always points to the operator

 Removing of protective guard F

! disconnect the plug

- for mounting protective guard, handle in reverse order

 Three handle positions

 Before using the tool

- ensure that accessory is correctly mounted and rmly

tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 60 seconds at highest no-load

speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

 This tool should not be used by people under the age

of 16 years

 Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

 SKIL can assure awless functioning of the tool only

when the correct accessories are used which can be

obtained from your SKIL dealer

 Use only grinding/cutting discs with a maximum

thickness of 8 mm and a spindle hole diameter of

22 mm

 For mounting/using non-SKIL accessories observe the

instructions of the manufacturer concerned

 Never use reducors or adaptors to t large-hole

grinding/cutting discs

 Never use accessories with a "blind" threaded hole

smaller than M14 x 21 mm

OUTDOOR USE

 Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

BEFORE USE

 Before using the tool for the rst time, it is recommended

to receive practical information

 Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

 Always mount auxiliary handle E

and protective

guard F

; never use the tool without them

 

or call the local utility company for assistance

(contact with electric lines can lead to re or electrical

shock; damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

 Do not work materials containing asbestos

(asbestos is considered carcinogenic)

 Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

 Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

 Follow the dust-related national requirements for the

materials you want to work with

 Be careful when cutting grooves, especially in

supporting walls (slots in supporting walls are subject to

country-specic regulations; these regulations are to be

observed under all circumstances)

 Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

 Do not clamp the tool in a vice

 Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

DURING USE

 Inrush currents cause short-time voltage drops; under

unfavourable power supply conditions, other equipment

may be aected (if the system impedance of the power

supply is lower than 0,25 Ohm, disturbances are unlikely

to occur); if you need further clarication, you may

contact your local power supply authority

Skil 9412 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info