Bedienungsanleitung Skil 9783 (Seite 9 von 172) (Alle Sprachen)

644812

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

• For mounting/using non-SKIL accessories observe the

instructions of the manufacturer concerned

• Useonlygrinding/cuttingdiscswithamaximum

thicknessof8mmandaspindleholediameterof22

• Never use reducors or adaptors to t large-hole grinding/

cutting discs

• Never use accessories with a “blind” threaded hole

smaller than M14 x 21 mm

OUtDOOR USE

• Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

BEFORE USE

• Before using the tool for the rst time, it is recommended

to receive practical information

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• Always mount auxiliary handle F 2 and protective guard

G 2; never use the tool without them

• Usesuitabledetectorstofindhiddenutilitylinesor

callthelocalutilitycompanyforassistance (contact

with electric lines can lead to re or electrical shock;

damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Donotworkmaterialscontainingasbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wearadustmaskandworkwithadust

extractiondevicewhenconnectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wearadustmaskand

workwithadustextractiondevicewhen

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Be careful when cutting grooves, especially in supporting

walls (slots in supporting walls are subject to country-

specic regulations; these regulations are to be observed

under all circumstances)

• Securetheworkpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Do not clamp the tool in a vice

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

DURING USE

• Inrush currents cause short-time voltage drops; under

unfavourable power supply conditions, other equipment

may be aected (if the system impedance of the power

supply is lower than 0,25 Ohm, disturbances are unlikely

to occur); if you need further clarication, you may

contact your local power supply authority

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• In case of current interruption or when the plug is

accidentally pulled out, release switch J 2 in order to

prevent uncontrolled restarting

AFtER USE

• After switching o the tool, never stop the rotation of the

accessory by a lateral force applied against it

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Mounting of accessories 2

! disconnecttheplug

- clean spindle A and all parts to be mounted

- tighten clamping ange B with spanner C while

pushing spindle-lock button D

! pushspindle-lockbuttonDonlywhenspindleA

isatastandstill

- for removing accessories handle vice-versa

! grinding/cuttingdiscsbecomeveryhotduring

use;donottouchthemuntiltheyhavecooled

down

! alwaysmountbackingpadwhenusingsanding

accessories

! neveruseagrinding/cuttingdiscwithoutthe

label(“blotter”)whichisgluedontoit(if

provided)

• Mounting of auxiliary handle F 5

! disconnecttheplug

- screw auxiliary handle F on the right, the top, or the left

of the tool (depending on the work to be carried out)

• Removing/mounting/adjusting of protective guard G 6

! disconnecttheplug

- open protective guard G by loosening screw H (donot

removeit)

- place protective guard G on the spindle collar of the

tool head and turn it to the required position

(depending on the work to be carried out)

! ensurethattheclosedsideoftheprotective

guardalwayspointstotheoperator

- fasten protective guard G by tightening screw H

• Before using the tool

- ensure that accessory is correctly mounted and rmly

tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 30 seconds at highest no-load

speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

• Electronic soft-start

Ensures reaching the maximum speed smoothly without

a sudden impact when tool is switched on

• On/o safety switch J 7

- switch on tool 7a

! beforetheaccessoryreachestheworkpiece,the

toolshouldrunatfullspeed

Skil 9783 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info