Bedienungsanleitung Skil 9785 (Seite 9 von 164) (Alle Sprachen)

758637

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

! grinding/cutting discs become very hot during

use; do not touch them until they have cooled

down

! always mount backing pad when using sanding

accessories

! never use a grinding/cutting disc without the label

(“blotter”) which is glued onto it

• Mounting of auxiliary handle E 5

! disconnect the plug

• Removing/mounting/adjusting of protective guard F 6

! disconnect the plug

- open protective guard F by loosening screw K

- place protective guard F on the spindle collar of the

tool head and turn it to the required position

(depending on the work to be carried out)

! ensure that the closed side of the protective

guard always points to the operator

- fasten protective guard F by tightening screw K

• Before using the tool

- ensure that accessory is correctly mounted and ﬁ rmly

tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 30 seconds at highest no-

load speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

• On/off safety switch H 7

- switch on tool 7a

! be aware of the sudden impact when the tool is

switched on

! before the accessory reaches the workpiece, the

tool should run at full speed

- switch off tool 7b

! before switching off the tool, you should lift it

from the workpiece

! the accessory continues to rotate for a short time

after the tool has been switched off

• Electronic soft-start (9785)

Ensures reaching the maximum speed smoothly without

a sudden impact when tool is switched on

• Grinding 8

- move the tool back and forth with moderate pressure

! never use a cutting disc for side grinding

• Cutting 9

- do not tilt the tool while cutting

- always move the tool in same direction as arrow on

tool head, in order to prevent the tool from being

pushed out of the cut in an uncontrolled manner

- do not apply pressure on the tool; let the speed of

the cutting disc do the work

- the working speed of the cutting disc depends on the

material to be cut

- do not brake cutting discs with side pressure

• Holding and guiding the tool

! while working, always hold the tool at the grey-

coloured grip area(s) 0

- always hold the tool ﬁ rmly with both hands, so you

will have full control of the tool at all times

- provide for a secure stance

- pay attention to the direction of rotation; always hold

the tool so, that sparks and grinding/cutting dust ﬂ y

away from the body

- keep ventilation slots J 2 uncovered

• Vibration level

The vibration emission level stated at the back of this

instruction manual (indicated by an asterisk) has been

measured in accordance with a standardised test given

in EN 60745; it may be used to compare one tool with

another and as a preliminary assessment of exposure to

vibration when using the tool for the applications

mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories, may

signiﬁ cantly increase the exposure level

- the times when the tool is switched off or when it is

running but not actually doing the job, may

signiﬁ cantly reduce the exposure level

! protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns

MAINTENANCE / SERVICE

• Always keep tool and cord clean (especially the

ventilation slots)

! do not attempt to clean ventilation slots by

inserting pointed objects through openings

! disconnect the plug before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skileurope.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol ! will remind you of this when the need for

disposing occurs

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 9785 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info