Bedienungsanleitung Skoda Superb - 2014 (Seite 211 von 252) (Englisch)

678350

211

Zoom out

Zoom in

Vorherige Seite

1/252

Nächste Seite

The mounting points are located on the metal bar of the lower sill on the un-

derside of your vehicle. The positions of these are embossed by means of

markings on the side surface of the lower sill » Fig. 181.

›

Support the base plate of the jack with its full area resting on level ground

and ensure that the jack is located in a vertical position at the jacking

point » Fig. 181 -



›

Position the lifting jack below the jacking point with the crank and move it up

until its claw encloses the web » Fig. 181 -



›

Continue turning up the jack until the wheel is just about lifted off the

ground.

WARNING

Notes for vehicle lifting

■

Choose a flat and firm surface for jacking the vehicle.

■

If the wheel has to be changed on a slope, first of all block the opposite

wheel with a stone or similar object to prevent the vehicle from unexpect-

edly rolling away.

■

Secure the base plate of the lifting jack with suitable means to prevent

possible moving. A soft and slippery ground under the base plate may move

the lifting jack, causing the vehicle to fall down. It is therefore always nec-

essary to place the lifting jack on a solid surface or use a wide and stable

base. Use a non-slip base (e.g. a rubber foot mat) if the surface is smooth,

such as cobbled stones, tiled floor, etc.

■

Only attach the lifting jack to the attachment points provided for this pur-

pose.

■

Always raise the vehicle with the doors closed.

■

Never position any body parts, such as arms or legs under the vehicle,

while the vehicle is raised with a lifting jack.

■

When the vehicle is raised, never start the engine.

CAUTION

It is important to ensure that the jack is correctly attached to the web of the

lower fork leg, otherwise there is a risk of damage to the vehicle occurring.

Anti-theft wheel bolts

Fig. 182

Principle sketch: Anti-theft

wheel bolt with adapter

Read and observe on page 206 first.

The anti-theft wheel bolts protect the wheels from theft. These can only be

loosened or tightened with the use of adapter

» Fig. 182.

›

Remove the full wheel trim or the caps of the wheel bolts.

›

Insert adapter

» Fig. 182 with the toothed side all the way into the inner

teeth in the head of the anti-theft wheel bolts

›

Push the wheel wrench onto the adapter

up to the stop.

›

Loosen or tighten the wheel bolt » page 207.

›

Remove the adapter.

›

Replace the wheel trim or the caps.

To be equipped for a possible wheel change, the adapter for the anti-theft

wheel bolts must always be kept in the vehicle. The adapter is stowed in the

tool kit.

Note

■

Note the code number which is embossed both on the adapter and also on

the end of each anti-theft wheel bolt. This number can be used to purchase a

replacement adapter from ŠKODA Original Parts if necessary.

■

The anti-theft wheel bolt set and adapter can be purchased from a ŠKODA

Partner.



208

Do-it-yourself

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skoda Superb - 2014 Seite 211

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Skoda Superb - 2014

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info