Bedienungsanleitung Skylink 68 - remote (Seite 1 von 2) (Englisch)

536967

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Chamberlain

Lift-Master

Sears

Wayne Dalton

Master Mechanic

Genie

(9 positions)

Genie

(12 positions)

Overhead Door

Pulsar/Allister/Allstar

Master Craft

Linear

M-O-M

Stanley

Multi-Code

Skylink

UR-100

The model 68 transmitter

has 12 columns of posts,

each column has 3 posts.

(see diagram C)

2a. To program the model

68, open the case with

a coin. (see diagram B)

2b. There are 2 ways to pro-

gram the model 68 so

that it will communicate

with your garage door

opener. Open your exist-

ing transmitter, (the unit

you currently use to open

your garage), or look at

the back of your garage

door opener. If you see a

column of small switches

go to point 2c in this

manual. If there are no

switches, go to point 2e.

Diagram B

Each column contains one

connector (see digram D)

for a total of 12 connectors.

Diagram D

Diagram E

If the connector is placed

on the top and middle posts,

that column is set on “ + ”

or “ON” or “CLOSE”. If the

connector is placed on the

middle and bottom posts,

that column is set on “ - ”

or “OFF” or “OPEN”. If the

connector is removed

completely, (not placed

on any posts), it is set

to “ 0 ” or the neutral

position. (see diagram E

for examples of how to

set a column to the three

different positions). When

removing a connector to

set a column to the neu-

tral position, save the con-

nector in case you change

the code at a later date.

2c. To move the connectors,

slide an opened paper clip

into the side of a connector

and lift. (see diagram F)

When repositioning con-

nectors, place a connector

on the two chosen posts,

then push down on the

connector with your finger.

Paper

Clip

Diagram F

Diagram C

USA

CANADA

390

318

310

315

300

310

STEP 2 - SET CODE CONNECTORS

Linear * Position 1 to 8 + OR -

M-O-M * Position 1 to 8 + OR -

Stanley (310) Canada Position 1 to 10 + OR - 11,12 set to ‘+’ or ‘-’

Stanley (300) Position 1 to 10 + OR - 11,12 set to ‘+’ or ‘-’

Multi-Code Position 1 to 10 + OR - 11,12 set to ‘+’ or ‘-’

Chamberlain Position 1 to 9 +, 0 (blank), OR -

Lift-Master Position 1 to 9 +, 0 (blank), OR -

Sears Position 1 to 9 +, 0 (blank), OR -

Wayne Dalton Position 1 to 9 +, 0 (blank), OR -

Master Mechanic Position 1 to 9 +, 0 (blank), OR -

Genie (9 positions) Position 1 to 9 + OR -

Genie (12 positions) Position 1 to 12 + OR -

Master Craft Position 1 to 12 + OR -

Pulsar/Allister/Allstar Position 1 to 9 +, 0 (blank), OR -

Overhead Door Position 1 to 9 +, 0 (blank), OR -

Code connector setting to match your opener/motor

1a. Locate frequency

switch on the bottom

of the transmitter:

(see diagram A)

Diagram A

1b. Determine the brand of your garage door

opener and set the frequency switch to the

corresponding position. (see chart 1)

STEP 1 - SET FREQUENCY SWITCH

Thank you for your purchase of the Skylink garage door

remote control, Model 68. There are 2 different steps

you need to setup in order to use this universal garage

door remote control to operate your existing garage door

opener. These 2 steps are:

1) Frequency switch – select the correct frequency

according to the brand of your existing garage door

opener.

2) Code setting – Set the jumper connectors on the

Model 68 so that they match the code setting of your

existing garage door opener.

Please follow the detailed instructions below in order to set-

up the Skylink Model 68 to work with your existing opener.

NOTE: Transmission range may be reduced with use

on a metal garage door.

PROGRAMMING THE TRANSMITTER

Diagram G

Set the connectors numbered 1 through 12 to match the

switches of your existing transmitter or receiver. If your

garage door opener is manufactured by (Stanley

, Genie

Multi-Code

, Linear

, Moore-O-Matic

) these switches

may only have two positions, (“ +, ON, CLOSED” and “ - ,

OFF, OPEN”). (see diagram G) Set the connectors on the

model 68 to “ + ” if your existing switches are either “+ ,

ON, CLOSE ” and set to “ - ” if your existing switches are

either “ -, OFF, OPEN”. Do not use the center position “ 0 ”.

Examples of how to set Model 68

*Please check the FAQ section from www.skylinkhome.com for very old Linear / M-O-M systems.

Chart 1

390

300/390

390

318

310

300/310

390

D/A

D/C

315/390

318

315/390

310

390

C/A

Brand of your opener

Set switch

to position

Set switch

to position

Frequency

USA CANADA

Model 68

Existing

Transmitter

‘+’ or ‘ON’ or CLOSE ‘0’ = BLANK

‘-’ or ‘OFF’ or ‘OPEN’

STEP 2 - SET CODE CONNECTORS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skylink 68 - remote Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info