Bedienungsanleitung Skylink GT-110 (Seite 1 von 3) (Englisch)

536962

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

1. INTRODUCTION

Model GT-110

Garage Door

Remote Control

2. INSTALLATION

Unplug the power cord of your garage door opener

before installation to ensure power is not connected.

WARNING

Garage One

The GT-100R Garage One

replaces most garage door “push buttons”

or “wall consoles”. There are 2 different kinds of “push buttons”.

1) Single button

2) Multi-Function Wall Console

1) Single button

If your garage door opener equips with a single button “push button”,

you can replace the existing push button with Skylink

Garage One

GT-100R. Please follow the procedures below.

1. Remove the existing push button by removing

the screws.

2. Disconnect the 2 wires that are connected to

the existing push button.

3. Connect these 2 wires to the 2 terminals on the

Garage One

GT-100R. Loosen the 2 screws

on the terminals, feed the 2 wires to the 2

terminals and tighten 2 screws to secure the

2 wires.

4. After connecting the 2 wires, the red LED under-

neath the push button will be on. The GT-100R

is now charging up. The GT-100R will be fully

charged when the buzzer emits a beep (approx

10 seconds to 1 minute depending on the brand

of garage door opener), the red LED will then

flash slowly. The GT-100R is now ready to operate.

5. Mount the Garage One

to the wall with 2 screws.

6. Straighten up the antenna on the GT-100R.

Remove

existing

wires

Garage One

GT-100R

4-button

keychain transmitter

(Battery included)

Mu lti-Function Wall Console for Chamberlain

, Lift-Master

, Sears Craftsman

Skylink

GT-100R Garage One

also has 3 buttons. It can

replace Chamberlain

, Lift-Master

, and Sears Craftsman

Multi-Function Wall Console directly. That means if you

have any one of these wall consoles, you can simply

remove the existing wall console and replace it with a

Skylink

GT-100R. To replace a multi-function wall

console mentioned above, follow the same proce-

dure as to replace a “Single button” wall console.

If your Chamberlain

, LiftMaster

and Sears Craftsman

Multi-Function Wall Console has more than 2 wires, the Skylink

GT-100R

should be installed in parallel with the original Multi-Function Wall Console.

Connect the 2 wires from the GT-100R to the 2 terminals marked “RED”

and “WHT” on your existing Multi-Function Wall Console. Polarity DOES

NOT matter. Note: Do not remove the existing wires from your Multi-

Function Wall Console.

2. INSTALLATION (CONT)

Genie

Deluxe Wall Console

For the Genie

Deluxe Wall Console, depending on whether

the “lock” feature will be used.

- If the “lock” feature will not be used, you can simply replace

the Genie

Deluxe Wall Console with a Skylink

GT-100R.

To replace a multi-function wall console, follow the same

procedure as to replace a “Single button” wall console.

- If the “lock” feature will be used, you need to connect the Skylink

GT-100R

in parallel with the Genie

Deluxe Wall Console and an additional trans-

former (sold separately) is needed. Follow the instructions below:

Parallel Connection

1. Remove the existing push button by removing

the screws.

2. Remove the 2 screws that secure the wires

on the Genie

wall console.

3. Connect one end of the extension wires provided

in this kit to the 2 terminals on the Genie

wall

console, the other end to the 2 terminals

on the GT-100R wall console.

Polarity DOES NOT matter.

Note: Do not remove the existing wires

from the Genie

wall console.

4. After connecting the 2 wires, the red LED under-

neath the push button will be on. The GT-100R

is now charging up. The GT-100R will be fully

charged when the buzzer emits a beep (approx

10 seconds to 1 minute depending on the brand

of garage door opener), the red LED will then

flash slowly. The GT-100R is now ready to operate.

5. Mount both w all consoles to the wall with screws.

6. Straighten up the antenna on the GT-100R.

7. Plug in the transformer (sold separately) to Skylink

GT-100R. (For Genie

Deluxe Wall Console only)

Rating of the transformer: 12V DC, 100mA

Diameter of DC plug : 3.5mm

Multi-Function Wall Console – Other Brands

For brands other than Chamberlain

, Lift-Master

, Sears Craftsman

and

Genie

, the Skylink

GT-100R should be installed in parallel with the

original Multi-Function Wall Console. Refer to “Parallel Connection” under

Genie

Deluxe Wall Console.

Extension

wires

Extension wires

2) Multi-Function Wall Console

Multi-Function Wall Console normally comes with 3 buttons that can be

used to:

1) operate the garage door opener lighting,

2) lock the receiver so it doesn’t accept remote control operation, and

3) push button for door opening / closing

Depending on the brand of garage door opener you have, the installation

is different.

Congratulations on your purchase of the Skylink

Garage One

, Garage

Door Remote Control System. This is a transmitter receiver kit where the

receiver simply replaces your existing garage door opener’s push button

or wall console. Installation is very simple, follow the instructions below

to install the Garage One

receiver GT-100R. This kit comes with the

following items:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skylink GT-110 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info