Bedienungsanleitung Skytec 54 kanaals DMX controller (Seite 3 von 10) (Deutsch, Englisch, Holländisch, Französisch)

490938

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

54-CHANNEL DMX CONTROLLER

Ref. no. : 154.050

INSTRUCTION MANUAL

General description

This compact DMX controller can control 54 channels in total which are spread over 9 groups

(projectors) with a maximum of 6 channels per group. The outgoing DMX addresses are pre-set to:

Projector 1 : addresses 1 to 6; Projector 2: addresses 7 to 12, etc. You only need to set the

appropriate start address on the connected equipment , i.e. 1, 7, 13, 25 etc. There are 6 functions

max. per start address available. This SkyTec DMX controller has a built-in memory for 9 different

programs of 50 steps each (scenes) allowing automatic control of different light effects. In each of

these scenes (steps) you can determine a combination of settings for the position of the mirror, the

light colour or the light intensity. When you run these steps in sequence, the connected disco light

effects produce the requested light pattern.

Connection

Connect the controller to the disco light effects (projectors or dimmer packs) via XLR leads. Set the

correct DMX start addresses on the connected units. Example: You have two DMX projectors and 3

DMX dimmer packs. Set the DMX addresses on these units to 1, 7, 13, 19 and 25.

Plug the mains adapter into the socket on the rear side and into a mains outlet. Switch the controller

on via the power switch at the rear side. A short confirmation signal is heard and the controller runs a

short test program after which the displays shows 0000.

Set up

The SkyTec DMX controller offers the possibility to couple the signals of the outgoing channels i.e. a

projector which is connected to group 3 (address 13) can run in a program that is controlled by group 1

(projector 1 on address no. 1). Keep the SELECT button pushed in until the message SET is

displayed. Once this message has disappeared after 4 seconds, you can select via the UP/DOWN

buttons the number of the light effect that you wish to couple. The selection is activated by pressing

the INSERT button. The SCENE display shows ON. Press the DELETE button to switch this function

off. OFF is now displayed. Shortly press the SELECT button to leave the set up mode.

Manual Operation

You can operate the connected light effects manually via the slider controls 1 to 6. Shortly press the

PROGRAM button until the display shows 0000. Push now the ‘PROJECTOR’ button. The displayed

figure becomes a ‘1’ with a dot next to it. This dot means that you can change the setting. Select the

required unit via the buttons ‘UP’ and ‘DOWN’. Set the light effect via the slider controls. Depending on

the connected light effect units, these controls allow you to set 256 steps on all used channels. It can

be the position of a mirror, a colour or the light intensity of a running light. To switch the manual

operation off, push the PROJECTOR button until 0 is displayed again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skytec 54 kanaals DMX controller Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info