Bedienungsanleitung Skytech 3002 (Seite 1 von 10) (Englisch)

603162

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

INSTALLATION AND OPERATING INSTRUCTIONS

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT

TO INSTALL OR OPERATE

Model: 3002

INTRODUCTION

This SKYTECH remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas

heating appliances. The system can be operated thermostatically or manually from the transmitter. The system operates on radio

frequencies (RF) within a 20-foot range using non-directional signals. The system operates one of 1,048,576 security codes that are

programmed into the transmitter at the factory; the remote receiver’s code must be matched to that of the transmitter prior to initial use.

Review COMMUNICATION SAFETY under theTRANSMITTER SECTION and THERMO SAFETY under the REMOTE RECEIVER

SECTION. These signal/temperature safety features shut down the appliance when a potentially unsafe condition exists.

REV. 4-19-12 Page 1

Skytech: 3002

The transmitter operates on (2) AAA-size 1.5V batteries. It is recommended that ALKALINE batteries always be used for

longer battery life and maximum operational performance. IMPORTANT: New or fully charged batteries are essential for

proper operation of the multi-function transmitter. Insert (2) AAA-size 1.5 V batteries into the battery compartment on the

back of the transmitter, positioning the (+) and (-) ends of the batteries as indicated on the casing. When the batteries are

inserted, gure #2 (with similar numbers) will display.

Fig. 1 Transmitter Front and Back Views

Note: If a LOW battery icon appears on the screen,

check the position of the batteries.

CAUTION: Due to the sensitive temperature-monitoring

components in the transmitter, it may be necessary to

allow the transmitter to stabilize to room temperature

before accurate room temperatures are displayed on

the screen. If the transmitter is activated from a

severe cold condition, it can take up to fteen minutes

for accurate temperature readings to appear.

1. BATTERY ICON - Symbol means battery power is low. Replace batteries within 2-weeks.

2. TIMER- Indicates time remaining before system shuts OFF, when timer-programmed; 9-hour maximum setting.

3. MODE- Indicates operation MODE of system. ON indicates the system is manually ON. OFF indicates the entire

system is turned OFF and THERMO indicates the system will automatically cycle ON/OFF, depending on the SET

temperature.

4. SET- Indicates desire SET room temperature for THERMO operation.

5. FLAME – Indicates burner/valve in ON position.

6. CLOCK – Indicates the current time in AM/PM

7. ROOM – Indicates CURRENT room temperature.

8. °F indicates degrees Fahrenheit (°C indicates degrees Celsius).

LCD DISPLAY FUNCTIONS

ROOM

SET

Fig. 2 LCD Display Functions

MODE

COVER CLOSED

MODE

TIMER

TIME

SET

SLIDE COVER

OPEN

AAA

BACK OF

TRANSMITTER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skytech 3002 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info