687274
62
Zoom out
Zoom in
Vorherige Seite
1/68
Nächste Seite
8.5 Resetting the Operation Inhibition after Detection of an
Arc Fault
If the red LED is glowing and the event number 4301 is shown on the display and/or in the event
list on the user interface of the inverter, the inverter has detected an electric arc and interrupts feed-
in operation.
There are two options for resetting the operation inhibition:
Reset the operation inhibition by tapping twice on the enclosure lid of the Connection Unit.
Reset the operation inhibition by parameter setting.
Reset the operation inhibition by tapping twice on the enclosure lid of the
Connection Unit
1.
Danger to life due to electric shock
Disconnect the inverter from any voltage sources (see the inverter installation manual).
2. Ensure that the PV modules, the connected DC cables and the connecting terminal plate for the
DC connection are not defective.
Repair or replace defective PV modules, DC cables or connecting terminal plate for the DC
connection.
3. Recommission the inverter (see inverter installation manual).
4. If the event with the event number 4301 appears in the display, immediately tap on the
enclosure lid twice in quick succession. Here, the operation inhibition can only be reset if the
event is showing in the display when you begin tapping.
This effects resetting of the operation inhibition and the inverter will start feeding in again. At
the same time, the blue LED can flash rapidly, indicating that there is an active WPS function.
The WPS function deactivates automatically after a short period.
Reset the operation inhibition by parameter setting
1.
Danger to life due to electric shock
Disconnect the inverter from any voltage sources (see the inverter installation manual).
2. Ensure that the PV modules, the connected DC cables and the connecting terminal plate for the
DC connection are not defective.
Repair or replace defective PV modules, DC cables or connecting terminal plate for the DC
connection.
3. Recommission the inverter (see inverter installation manual).
4. Activate the user interface (see Section5.1, page20).
5. Log into the user interface as an Installer Logging Into the User Interface.
6. Reset the operation inhibition by setting one of the following parameters:
8 Troubleshooting
SMA Solar Technology America LLC
User ManualSB30-77-1SP-US-40-BA-en-1162
62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für SMA Sunny Boy 5.0-US wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info