Bedienungsanleitung SMC IDF1E-10 (Seite 18 von 33) (Englisch)

658159

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

2 Transportation / Installation

2 - 2

2-2 Installation

2-2-1 Location

The product should not be used or stored in the circumstances as follows. Those

circumstances will cause not only malfunction but also failures.

• Environment where the product is exposed to

rainwater, moisture vapor, salty water, oil and

so on.

• Locations where dust or particles are.

• Locations where inflammable or explosive gas

are.

• Locations where corrosive gas, solvent,

combustible gas are.

• Locations that receive direct sunlight or where

radiant heat is generated.

• Locations where ambient temperature is

beyond following range:

On-stream: 2 ~ 40

Storage: 0 ~ 50

C (when there is no drain

water inside of the piping)

• Locations where temperature changes rapidly.

• Locations where strong electromagnetic noise

is generated (locations where electromagnetic

field, strong magnetic field, surge is generated)

• Circumstances where static electricity is

produced or discharged through the body of the

product.

• Locations where strong high frequency wave is

generated.

• Locations where danger of thunder is apparent.

• Locations by loading on vehicles, marine

vessels, and so on.

• Locations whose altitude is higher than 2,000

meters.

• Circumstances where strong vibration or impact

are transmitted.

• Circumstances where too much force and

weight are put on the body of the product that

causes it to deform.

• Circumstances where enough spaces cannot

be taken to do maintenance (in the plant where

the product is operated).

Spaces needed for maintenance

Front : 6001500 mm

Rear : 600400 mm

Top : 600400 mm

Right : 600400 mm

Left : 600400 mm

• Locations the ventilation grille of the product

can be blocked.

• Place where rejection style air of air

compressor or other driers (hot wind) is inhaled.

2-2-2 Anchorage

• The air dryer should be installed on a vibration-free, stable, horizontal flat surface.

• Refer to “Chapter6 6-2 Dimensions” for the dimensions.

• IDF4E~15E should be bolted by anchor bolts to prevent falling. We recommend the anchor bolt sets that

we are selling separately as accessories.

2-2-3 Air piping

• Connection to the inlet and outlet of compressed air should be made removable by using union and so on.

• Pressing the hexagonal fitting with screw wrench and so on, connect the air piping fittings to the body.

• When mounting any part such as an air filter on the fitting at the compressed air inlet or outlet port, support the

part to prevent excessive force from being applied to the product.

• Be careful not to let the vibration of the air compressor transmit.

• If the temperature of compressed air on the inlet side is higher than 50

C, place an aftercooler after the air

compressor. Or, make the temperature of the place where the air compressor is installed lower than 50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

SMC IDF1E-10 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info