Bedienungsanleitung Smeg CMS4303X (Seite 19 von 32) (Englisch)

682754

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

A marked inside the tank (equal to one 100 ml pack); then

add water (one litre) up to level B; and put the water tank

back in. Press ;

6. EMPTY GROUND CONTAINER AND DRIP TRAY (g. 27):

remove, empty and replace the drip tray (A14) and the

ground container (A4). Press ;

7. PLACE 2.5l CONTAINER UNDER OUTLET PRESS OK TO START

DESCALING :

Place an empty container with a minimum capacity of 2.5

litres under the hot water/steam spout (C6) and coee

spouts (A13) (g.8);

Danger of burns!

Hot water ows out of the hot water/steam spout which contains

acid. Take care to avoid contact with splashes of this solution.

8. Press to conrm that you have added the de-scal-

ing solution. The display shows DESCALING PLEASE WAIT

: the de-scale programme starts and the de-scaler liquid

comes out of the hot water/steam and coee spouts. A

series of rinses and pauses is automatically carried out to

remove all the scale residues from the inside of the coee

machine;

After about 25 minutes, de-scaling stops:

9. RINSE AND FILL WATER TANK UP TO MAX LEVEL (g.41): the

appliance is now ready for a fresh water rinsing cycle. Emp-

ty the container used to collect the de-scaler solution and

extract the water tank, empty, rinse under running water,

ll with fresh water up to the MAX level and put back in the

appliance;

10. PLACE 2.5l CONTAINER UNDER OUTLET PRESS OK TO START

RINSING: Place the container used to collect the de-scaler

solution empty under the coee spouts and hot water/

steam spout (g.8) again and press ;

11. Hot water is delivered rst from the coee spouts and the

display shows RINSING PLEASE WAIT ;

12. When the water in the tank has run out, empty the contain-

er used to collect the rinsing water;

13. (If the lter is installed) INSERT FILTER INTO ITS HOUSING

(g.42). Press and extract the water tank, rein-

sert the water softener lter if removed previously;

14. RINSE AND FILL WATER TANK UP TO MAX LEVEL (g.41): Fill

the tank up to the MAX level with fresh water;

15. INSERT WATER TANK (g.6): Put the water tank back in the

appliance;

16. PLACE 2.5l CONTAINER UNDER OUTLET PRESS OK TO START

RINSING :

Place the empty container used to collect the de-scaler

solution under the hot water/steam spout (g.8) and press

;

17. Hot water is delivered from the hot water/steam spout and

RINSING PLEASE WAIT is displayed.

18. EMPTY DRIP TRAY (g.27): At the end of rinsing, remove,

empty and replace the drip tray (A14) and grounds contain-

er (A4): press ;

19. For a few seconds DESCALE COMPLETE will be shown on the

display; the appliance turn o.

De-scaling is complete.

Please note:

• If the de-scaling cycle is not completed correctly (e.g. no

electricity) we recommend repeating the cycle;

• After de-scaling, it is normal for the grounds container (A4)

to contain water.

• If the water tank has not been lled to the max level, at the

end of de-scaling, the appliance requests a third rinse to

guarantee that the de-scaler solution has been complete-

ly eliminated from the machine's internal circuits. Before

starting rinsing, remember to empty the drip tray;

• The appliance may request de-scaling cycles at very short

intervals. This is normal and due to the appliance’s ad-

vanced control system

PROGRAMMING WATER HARDNESS

The DESCALING NEEDED - PRESS OK TO START (~45min)

message is displayed after a period of time established according

to water hardness.

The appliance default is pre-set in manufacturing at "level 4"

hardness. The machine can also be programmed according to

the hardness of the mains water in the various regions so that

the machine needs to be de-scaled less often.

Measuring water hardness

1. Remove the "Total hardness test" indicator paper (C1) pro-

vided from its packaging, attached to the instructions.

2. Immerse the paper completely in a glass of water for about

one second.

3. Remove the paper from the water and shake lightly. After

about a minute, 1, 2, 3, or 4 red squares form, depending on

the hardness of the water. Each square corresponds to one

level.

soft water - level. 1

slightly hard water - level. 2

hard water - level. 3

very hard water - level. 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Smeg CMS4303X Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Smeg CMS4303X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info