Bedienungsanleitung Smeg FP 800 A (Seite 11 von 27) (Englisch)

74993

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

Instructions for the User

8.0.3 Programming

Cooking duration: the 2nd button can be pressed to set the cooking duration. Before it can be set,

the thermostat must be turned to the cooking temperature required and the function selector knob to any

setting. To set the cooking duration, proceed as follows:

• Press the key for 1 / 2 seconds; the pointer will locate on 12 (Fig. 1).

• The cooking duration can be set using the and keys: each pressure on the

key adds 1 minute to the cooking duration (figure 2 shows a cooking duration of

1 hour).

• Once the duration required is obtained, cooking will start about 6 seconds after the

last pressure on or .

• Once cooking has started the display will show the current time, represented by

the constantly illuminated segments, and the minutes left to the end of the cooking

time, represented by the flashing segments (each flashing segment means 12

minutes of cooking time left).

• At the end of the cooking time the timer will switch the oven heating elements off, the beeps will start

to sound and the numbers on the dial will flash.

• The duration can also be reset by resetting the program selected: pressing the central key for 2

seconds will delete the duration set and the oven will have to be switched off in manual mode.

Warning: it is not possible to set cooking durations of more than 6 hours.

Starting cooking: as well as setting a cooking duration, the cooking start time can also be set (with a

maximum delay of 12 hours in relation to the current time). To set the cooking start/end time, proceed as

follows:

• Set the cooking duration as described in the previous point.

• Within 6/7 seconds of the last pressure on the or keys, press the key again to set the

cooking start time. The current time will appear on the display with internal segments illuminated to

show the end of cooking time. Use the and keys to set the cooking start time.

• 6/7 seconds after the last key is pressed, the display will show the current time and the cooking start

and end times, which will be represented by the illuminated inside segments. The display segments

will be constantly illuminated as long as the current time is not the same as the cooking start time; as

soon as the current time reaches the set starting time, all the inside segments will start to flash,

indicating that the oven has started cooking.

• At the end of the cooking time the timer will switch the oven heating elements off, the beeps will start

to sound and the numbers on the dial will flash.

• To reset the whole program set, keep the central key pressed for 2 seconds: if cooking has already

started, the oven will have to be switched off by hand.

• Here we can see a programming example: the current time is 19:06 and cooking is

programmed to start at 20:00 and end at 21:00 hours.

• At 20:00 hours the inside segments between 8 and 9 will start to flash, while the

hours hand will remain still.

Warning: for the oven to start cooking operations after the programming procedures just

described, the thermostat and function selector knob must correctly set on the temperature and

function required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Smeg FP 800 A Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Smeg FP 800 A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info