Bedienungsanleitung Smeg KIV 1007 X (Seite 20 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

109741

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

centre line printed on the drilling template must

correspond to the centre line drawn on the wall, and the

bottom edge of the drilling template must correspond to

the bottom edge of the hood.

3. Place the lower support bracket on the perforation

diagram making it coincide with the traced triangle, mark

the two external holes and perforate. Remove the

perforation diagram, insert two wall-dowels and fix the

support bracket of the hood with two 5x45 mm screws.

4. Hang the hood onto the lower bracket.

5. Adjust the distance of the hood from the wall.

6. Adjust the horizontal position of the hood.

7. Using a pencil mark the cooker hood permanent drill hole

inside the suction group.

8. Remove the hood from the lower bracket.

9. Drill at the point marked (Ø8mm).

10. Insert 1 wall screw anchor.

11. Apply the flues support bracket G to the wall adherent to

the ceiling, use the flues support bracket as a perforation

diagram (if present, the small slot on the support must

coincide with the line drawn previously on the wall) and

mark two holes with a pencil. Make the holes (Ø8mm),

and insert 2 dowels.

12. Fix the chimney support bracket to the wall using two

5x45mm screws.

13. Hook the hood onto the bottom bracket.

14. Fix the hood into its final position on the wall

(ABSOLUTELY ESSENTIAL).

15. Connect a pipe (pipe and pipe clamps not provided, to be

purchased separately) for discharge of fumes to the

connection ring located over the suction motor unit.

If the hood is to be used in ducting version, the other end

of the pipe must be connected to a device expelling the

fumes to the outside. If the hood is to be used in filter

version, then fix the deflector F to the chimney support

bracket G and connect the other extremity of the pipe to

the connection ring placed on the deflector F.

16. Connect the electricity.

17. Apply the chimney stacks and fasten them at the top to

the chimney support G (17b) using 2 screws (17a)

18. Slide the bottom section of the chimney down until it

completely covers the suction unit and slots into the

housing provided on top of the hood.

Remount the carbon filter frame and the fat/s filter/s and check

the perfect functioning of the hood.

Description of the hood

Fig. 1

1. Control panel

2. Grease filter

3. Grease filter release handle

4. Halogen lamp

5. Vapour screen

6. Telescopic chimney

7. Air outlet (used for filter version only)

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

Model with switch-board having 6 push-buttons

1. Switch ON/OFF Pilot-lights:

press to switch on/off lights.

2. Switch OFF suction / ON speed

(rating) of suction speed 1:

press this switch once turn off the

speed (rating) of suction function

that has been selected or (if no

speed rating of suction function

select the speed (rating) of suction

speed 1, press again and keep

pressed to activate the time-

function for 20 minutes (blinking

light), following this the cooker

hood will swittch off.

3. Speed selecting button suction

speed 2: press this switch once to

select the speed rating of suction

speed, press again and keep

pressed to activate the time-

function for 15 minutes (blinking

light) following this the cooker-

hood will switch off.

4. Speed selecting button suction

speed 3: press this switch once to

select the speed rating of suction

speed, press again and keep

pressed to activate the time-

function for 10 minutes (blinking

light) following this the cooker-

hood will switch off..

5. Speed selecting button (speed

rating) for intensive suction

(with timer): press to select the

suction-speed (rating) , the

functioning-time is 5 minutes

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Smeg KIV 1007 X Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info