Bedienungsanleitung Smeg ksem 90 (Seite 4 von 16) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

132013

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Description of the hood - Fig. 1

1) Exhaust unit with control panel and lights.

2) Hood shell

3) Telescopic flue

4) Holders

Installation

The installed appliance must not be less than 65 cm. above

electric burners and 75 cm. above gas or mixed burners.

The duct must be directed straight to the ceiling or

to the wall behind.

The duct must be slightly slanted upwards (about 10%)

in horizontal sections to expel air easily to the outside.

Electrical connection: The electrical tension must

correspond to the tension noted on the label placed inside

the cooker hood. Connect the electrical plug, where

provided, to the an easily accessible outlet in conformity

with local standards in force.

Where an electrical plug is not provided (for direct

connection to electrical network) place a standards approved

bipolar switch with an aperture distance of not less than

3mm (accessible) from the contacts.

Fastening the hood

a) With a pencil trace a line on the wall corresponding with

the centre line of the hood to facilitate positioning and

installing of the hood (Fig. 2).

b) Position the template correctly position and make two

Ø8 mm. holes (Fig. 3 - the lower edge of the template

corresponds with the lower edge of the hood and the

hatched line must correspond with the line traced on

the wall behind).

c) Insert two expansion plugs in the holes (Fig. 3).

d) Fasten the hood bracket with two 5x45 screws (Fig.

3).

e) Hook the hood to the bracket and level it by turning the

screws on the side behind the hood outlet as necessary

(Fig. 4).

f) Make sure the line traced on the wall is perfectly central

compared to the hood (Fig. 5).

g) Once the right position is established, mark with a

pencil the positions of the fastening bottom and upper

holes (Fig. 5) and measure the distance between the

connecting ring and the point where the exhaust duct

is to pass in order to establish the length of the duct.

h) Disassemble the upper support B from the telescopic

flue by removing the two screws C (one on each side)

and put them aside for future use (Fig. 6).

i) Remove the two screws joining deflector D to upper

support B and put them aside for future use (Fig. 6)

j) Fasten the upper support B ( Fig. 6) of the telescopic

flue to the wall behind and to the ceiling on the hood

perpendicular; for this operation make four Ø8 mm.

holes, insert the expansion plugs and fasten the

support with four 5x45 mm. screws.

The centre axis of the support must coincide with the

line drawn on the wall.

For filter version only (with carbon filter mounted

inside the exhaust unit)

Remount the deflector under the telescopic flue support

with two screws (see point “i”); the deflector will reroute

fumes inside the room.

k) Remove the hood and make four Ø8 mm. holes on the

previously marked points and insert the expansion

plugs (Fig. 7).

l) Before positioning the hood, fasten a duct to the

connecting ring of the internal exhaust unit and pass

the duct through the hood outlet hole.

m) Fasten the hood firmly with four screws, two in the

upper holes (plus two washers), two in the bottom

ones (Fig. 7 - the screws in the bottom holes also serve

to fasten the holder hook).

n) Connect the discharge pipe for venting cooking fumes

to the outside (exhaust version) or connect the pipe

directly to the deflector (filter version).

o) Finally fasten the telescopic flue with four screws by

inserting them from the outside in the two top and bottom

holes on the right and left sides of the flue (Fig. 6).

Assembly of the shelf (Optional)

Fasten the four side supports at the desired height and

place the shelf on them (Fig. 8).

Cleaning

To clean the outside of the hood, a cloth moistened with

denatured alcohol or neutral liquid detergents.

Do not use products that contain abrasives.

When cleaning glazed stainless steel parts, pass the cloth

in the same direction as the glazing.

Attention

To avoid risk of fire, observe these rules for cleaning the

appliance and replacing and cleaning the filters.

Follow instructions closely.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Smeg ksem 90 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info