Bedienungsanleitung Smeg KSEV-910 X1 (Seite 19 von 107) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

109389

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

air-exit perforations are not visible. The chimneys in which

this operation is possible are recognizable by their bracket

fixing points G which are repeated also in the lower side of the

upper section of the chimney (see installation sequence 20a-

20b).

Attention! for all pre-assembled models:

the mounting operations “1, 2, 3” should not be taken into

consideration, for installation begin at operation “4”.

1. Rest the suction unit on a flat surface and thread the lower

part of the hood onto it (consult the figure corresponding

to the model in possession - Fig. 1C/8C - 1D/8D - 1I/8I -

1E/8E - 1F/8F - 1G/8G - 1H/8H - 1R/8R - 1N-1O-1P).

2. Make all the electrical connections between the two parts

(Fig. 9).

3. Permanently fix the cooker hood to the suction group with

the screws (consult the figure corresponding to the model

in possession - Fig. 1C/8C - 1D/8D - 1I/8I - 1E/8E - 1F/8F

- 1G/8G - 1H/8H - 1R/8R - 1N-1O-1P).

4. Using a pencil, draw a line on the wall, extending up to the

ceiling, to mark the centre. This will facilitate installation

(Fig. 10).

5. Rest the drilling template against the wall: the vertical

centre line printed on the drilling template must

correspond to the centre line drawn on the wall, and the

bottom edge of the drilling template must correspond to

the bottom edge of the hood: bear in mind that, when

installation is complete, the underside of the hood must

be at least 50 cm above the cooker top in the case of

electric cookers, and at least 65 cm above the cooker top

in the case of gas or mixed cookers.

6. Place the lower support bracket on the perforation

diagram making it coincide with the traced triangle, mark

the two external holes and perforate. Remove the

perforation diagram, insert two wall-dowels and fix the

support bracket of the hood with two 5x45 mm screws

(Fig. 10).

Attention: only the models illustrated in Fig. 1Q/10Q:

Fix the central bracket with two screws and wall-dowels

above the lower bracket (see perforation diagram for

positioning the holes).

7. If supplied dismantled, fix the hooks to the side of the

aspiration group with two screws (fig. 10a). Hang the

hood onto the lower bracket.

8. Adjust the distance of the hood from the wall.

9. Adjust the horizontal position of the hood.

10. Using a pencil mark the cooker hood permanent drill hole

inside the suction group (1 or 2 fixing points are

necessary for permanent mounting) (Fig. 11).

11. Remove the hood from the lower bracket.

12. Drill at the point marked (Ø8mm) (Fig. 12).

13. Insert 1 or 2 wall screw anchors according to requirement.

14. Apply the flues support bracket „G“ to the wall adherent to

the ceiling, use the flues support bracket as a perforation

diagram (if present, the small slot on the support must

coincide with the line drawn previously on the wall) and

mark two holes with a pencil. Make the holes (Ø8mm),

and insert 2 dowels (Fig. 13).

15. Fix the chimney support bracket to the wall using two

5x45mm screws.

16. Hook the hood onto the bottom bracket.

17. Fix the hood into its final position on the wall

(ABSOLUTELY ESSENTIAL) (Fig. 14).

18. Connect a pipe (pipe and pipe clamps not provided, to be

purchased separately) for discharge of fumes to the

connection ring located over the suction motor unit.

If the hood is to be used in ducting version, the other end

of the pipe must be connected to a device expelling the

fumes to the outside. If the hood is to be used in filter

version, then fix the deflector F to the chimney support

bracket G and connect the other extremity of the pipe to

the connection ring placed on the deflector F (Fig. 13-

15).

19. Connect the electricity.

Attention: only the models illustrated in Fig. 1Q:

Continue from the installation sequence number 23.

20. Apply the chimney stacks and fasten them at the top to

the chimney support „G“ (20b) using 2 screws (20a)

(Fig. 16).

Only for model with optical fibers point lighting (Fig.

1G):

Check that the chimneys may be removed to permit

access to the optical fibers lamp housing area.

Only for the model with control panel on chimney flue

(Fig. 1L- 17):

Insert the command plate from the motor group through

the chimney flue slit from the inside towards the outside

(20c).

Carry out the connection of the control panel to the

command plate.

Attention! The terminal pivot on the plate MUST

correspond to the drill hole on the connection block

situated at the back of the control panel.

21. Slide the bottom section of the chimney down until it

completely covers the suction unit and slots into the

housing provided on top of the hood (Fig. 18).

22. Fix the lower section of the chimney with two screws (only

for the model in Fig. 1H/19H-1J/19J-1L/19L-1M/19M-

1N/19N-1O/19O-1P/19P).

23. Only the models illustrated in Fig. 1Q:

• Put the flues unit on the suction unit.

Connect the electricity between the two parts (Fig. 9).

• Fix the flue units definitively to the suction unit with the

screws (consult the figure corresponding to the

model in possession) (Fig. 8Q).

Attention! Check that the lower section of the flue fits

onto the central bracket (Fig. 20).

• Fix the upper section of the flue units to the flues support

bracket with two screws (Fig. 16).

Remount the carbon filter frame and the fat/s filter/s and check

the perfect functioning of the hood.

Smeg KSEV-910 X1 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info