Bedienungsanleitung Smeg KSEV-910 X1 (Seite 23 von 107) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

109389

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

Maintenance

ATTENTION! Before performing any maintenance operation,

isolate the hood from the electrical supply by switching off at

the connector and removing the connector fuse.

Or if the appliance has been connected through a plug and

socket, then the plug must be removed from the socket.

Cleaning

The cooker hood should be cleaned regularly (at least with the

same frequency with which you carry out maintenance of the

fat filters) internally and externally. Clean using the cloth

dampened with neutral liquid detergent. Do not use abrasive

products. DO NOT USE ALCOHOL!

Warning:

Failure to carry out the basic cleaning recommendations of the

cooker hood and replacement of the filters may cause fire

risks.

Therefore, we recommend oserving these instructions.

The manufacturer declines all responsibility for any damage to

the motor or any fire damage linked to inappropriate

maintenance or failure to observe the above safety

recommendations.

Grease filter

Fig. 2

This must be cleaned once a month (or when the filter

saturation indication system – if envisaged on the model in

possession – indicates this necessity) using non aggressive

detergents, either by hand or in the dishwasher, which must

be set to a low temperature and a short cycle.

When washed in a dishwasher, the grease filter may discolour

slightly, but this does not affect its filtering capacity.

To remove the grease filter B, pull the spring release handle.

Charcoal filter (filter version only)

Fig. 3

It absorbs unpleasant odours caused by cooking.

The charcoal filter can be washed once every two months (or

when the filter saturation indication system – if envisaged on

the model in possession – indicates this necessity) using hot

water and a suitable detergent, or in a dishwasher at 65°C (if

the dishwasher is used, select the full cycle function and leave

dishes out).

Eliminate excess water without damaging the filter, then

remove the mattress located inside the plastic frame and put it

in the oven for 10 minutes at 100° C to dry completely.

Replace the mattress every 3 years and when the cloth is

damaged.

Remove the filter holder frame by turning the knobs (g) 90°

that affix the chimney to the cooker hood.

Insert the pad (i) of activated carbon into the frame (h) and fit

the whole back into its housing (j).

It is possible to use a traditional carbon filter, neither

washable nor regenerable, to be replaced every 3 - 4 months.

The filter holder frame of the carbon filter is welded together;

the eventual frame supplied with the hood is not, therefore, to

be used.

Insert it into its housing and fix it turning the 2 plastic knobs.

Replacing lamps

Disconnect the hood from the electricity.

Warning! Prior to touching the light bulbs ensure they are

cooled down.

For models shown in Fig. 1E + Fig. 4E:

1. Press on the lamp cover and release to open.

2. Replace the damaged light bulb.

Only use halogen bulbs of 20W max (G4), making sure

you do not touch them with your hands.

3. Close the lamp cover (it will snap shut).

For models shown in Fig. 1N/O + Fig. 4N/O:

1. Unscrew the lamp cover.

2. Replace the damaged light bulb.

Only use halogen bulbs of 20W max (G4), making sure

you do not touch them with your hands.

3. Refit the lamp cover.

For models shown in Fig.1+Fig.4

(A/B/C/D/F/H/I/K/P/Q/S/T/U/V):

1. Extract the lamp cover by levering it off with a small

screwdriver or similar tool.

2. Replace the damaged light bulb.

Only use halogen bulbs of 20W max (G4), making sure

you do not touch them with your hands.

3. Close the lamp cover (it will snap shut).

For models shown in Fig. 1J + Fig. 4J:

1. Use a small screwdriver as a lever on the borders of the

lamp in order to remove the lightbulb.

2. Unthread the connector „a“.

3. Slide out the lightbulb to be replaced and replace with a

new 12V 20W 30° Ø35 12V GU4 PHILIPS STANDARD

LINE code 425409.

4. Carry out the replacement and mount the new lightbulb by

following instructions in the reverse.

For models shown in Fig. 1G + Fig. 5G:

Dismount the chimneys: remove the two screws (20 a)

that attaches the upper chimney to the support „G“ (Fig.

16).

Remove the box „q“: remove the screw „r“ that secures

the cooker hood.

Remove the lamp housing „s“: remove the screws „t“

that position the housing in the lamp housing area.

Extract the damaged lamp.

Use only PHILIPS type 14515 (GX 5.3) 12V - 75W

halogen bulbs..

Reposition and secure the lamp housing „s“ and the box

„q“ and remount the chimneys.

For models shown in Fig. 1K + Fig. 4K:

Certain versions of this cooker hood provide for an

incandescent lamp at 40W maximum (E14), remove the

lamp cover to access the lamp housing and carry out any

replacements.

Only for the illustrated model in Fig. 1L + Fig. 6L:

1. Open the front panel “v” upwards, which holds the lamp in

place, ensuring to hold the lamp “z” with one hand.

2. Replace the damaged lamp with one of identical technical

characteristics.

Attention! To guarantee the equivalent quality of lighting,

it is recommended to use the same type of lamp bulb:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Smeg KSEV-910 X1 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info