Bedienungsanleitung Smeg P875P (Seite 9 von 15) (Englisch)

660454

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Instructions for the user

7.2.3 Plate lock-out

20 seconds after the last power adjustment, the plate switches to "lock-out" status and no more

adjustments to the power levels set will be possible. This function, indicated by a dot which appears

alongside the power level (see side), is provided to ensure greater safety in use of the hob.

The "lock-out" can be eliminated by keeping the or symbol of any push-button pressed for 2-3

second.

7.2.4 Plate layout

REAR LEFT

REAR RIGHT

MIDDLE

FRONT LEFT

FRONT RIGHT

7.2.5 Timer (on some models only)

Some models are equipped with cooking timer.

To activate the timer, proceed as follows: with the plates on or off;

1. keep the symbol pressed for a few seconds (the two displays in the middle of the screen-

printing will switch on, showing a flashing figure 30) (if the plate is on, the power display value will

drop by one point, but it will return to the previous value at once);

2. press the or symbols to increase or reduce the cooking time and set it on the number of

minutes required (the number of minutes flashes);

3. seconds after the last key is pressed, the minutes display will stop flashing and the figure 0 on the

power display will start to flash.

4. The power level must be set within another 5 seconds as described in points 7.2.1 / 7.2.2;

otherwise the hob will switch off automatically. If the power is not adjusted within 5 seconds, the

timer will still start the count.

5. Timed cooking will start 5 seconds after the last power adjustment.

At the end of the time set, 3 BEEPS will sound in sequence; they are repeated 5 times at 5 second

intervals.

To stop the beeps in manual mode, simply press the or symbol of any push-button.

7.2.6 Modifying the data set

During timed cooking, each single pressure on the or symbols increases or reduces the power of

the plate. 5 seconds after the last button is pressed, a BEEP will sound and the display showing the

time left will start flashing. The or symbols can now be pressed to increase or decrease the

cooking time.

A few seconds after the last cooking time adjustment, the minutes display will also stop flashing and

the count will restart with the new settings.

7.2.7 Residual heat

Each plate is equipped with a residual heat warning device.

After any plate is switched off, a flashing " " may appear on the display.

This warns that the cooking zone concerned is still very hot.

Cooking can be restarted while the is flashing; proceed as described in points "7.2.1 / 7.2.2".

7.2.8 Control circuit board thermal protection

If the plates overheat the internal electronics board, the heat will be switched off automatically. This

switches off power to the front plates, and the letters and flash alternately on the power leds.

If the electronics board does not cool down, power to all the plates is switched off, and the power leds

display the text . Cooking can be resumed once the temperature has dropped below

the safety threshold.

7.2.9 Operator Error

If the user makes a mistake when using the push-buttons, an appears on the power display; it

will remain there as long as the user continues to press the button being used incorrectly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Smeg P875P Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Smeg P875P

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info