Bedienungsanleitung Smeg pva140 (Seite 6 von 16) (Englisch)

336356

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Instructions for the installer

4. Gas connection

If the appliance is installed on an oven, you must avoid running the gas tube round the

back of the oven in order to avoid overheating.

Connection to the gas supply network can be made using a rigid copper hose or a flexible

steel hose with a continuous wall and in compliance with the guidelines established by

the applicable standard. To facilitate the connection, connector A on the back of the

appliance can be orientated laterally; loosen hexagonal nut B, twist connector A into the

desired position then retighten hexagonal nut B (it is sealed with a rubber gasket). Once

the operation is complete, check the hose fittings for leaks using a soapy solution; never

use a flame. The hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. To set

it up for supply using other types of gas, see “5. ADAPTATION TO DIFFERENT TYPES

OF GAS”. The gas inlet connection is threaded ½” for external gas (ISO 228-1).

Connection with a rigid copper hose: The connection to

the gas supply network must be made in such a way that it

does not cause stresses of any type on the appliance. The

connection can be made using the adapter unit D with

double cone, always inserting gasket C (provided) in

between.

Connection with a flexible steel hose: use only

continuous wall stainless steel hoses that comply with the

applicable standards, making sure to always insert gasket

C (provided) between connector A and flexible hose E.

Installation with the flexible hose must be carried out so that the length of the piping

does not exceed 2 metres when fully extended; make sure that the hoses do not come

into contact with moving parts and that they are not crushed in any way.

4.1 Connection to liquid gas

Use a pressure regulator and make the connection on the gas cylinder following the

guidelines set out in the regulations in force. Make sure that the feed pressure

complies with the values indicated in the table in “5.2 Adjustment for liquid gas”.

4.2 Room ventilation

The room containing the appliance should have a permanent air supply in accordance

with the standards in force. The room where the appliance is installed must have

enough air flow for the regular combustion of gas and for the air exchange needed in

the room itself. The air vents, protected by grills, must be suitably dimensioned in

compliance with the current regulations and positioned so that no part of them is

obstructed.

The room must be kept adequately ventilated in order to eliminate the heat and

humidity produced by cooking: in particular, after prolonged use, you are

recommended to open a window or to increase the speed of any fans.

4.3 Extraction of the combustion products

Installation must first comply with the regulations in force and must comply with the

regulation distances and positions.

Hoods set to Recirculation mode may be used only if all other ventilation requirements

and regulations are met in full.

Combustion gases may also be discharged by means of hoods connected to a flue or

ducting providing a reliable natural draft, or a fan extraction system.

An effective extraction system requires careful design by an authorised specialist,

After installation, the installer must issue a certificate of compliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Smeg pva140 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Smeg pva140

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info