Bedienungsanleitung Smeg SE 2931 ID (Seite 13 von 17) (Englisch)

77271

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

What to do if trouble occurs

Interference with and repairs to the appliance by unqualified

persons are dangerous as they can result in electric shock, or

short circuit. Do no interfere with or try to repair the appliance;

this could cause injury and damage to the appliance. Therefore

always have such work done by an expert, e.g. the technical

Customer Service.

Please note

If your appliance is faulty, please check whether you can remove

the problem yourself by consulting these instructions for use.

But there are some problems described below that you can

fix yourself.

The fuses blow regularly?

Contact a technical customer service or an electrician!

You can't switch you induction hob on?

• Has the wiring system (fuse box) in the house blown a fuse?

• Has the hob been connected to the mains?

• Have the sensor buttons been locked (child safety device), i.e.

an L is shown in the display?

• Are the sensor keys partly covered by a damp cloth, fluid or a

metallic object? Please rectify.

• Are you using unsuitable cookware? See the section on

“Cookware for induction hobs”.

The symbol will blink and a time-limited continuous

signal will sound.

Food which has boiled over, cookware or other items are causing

the touch control sensor buttons to be consistently operated.

Remedy: clean the surface or remove the item.

To delete the symbol press the same button or switch the hob

off and on.

Error code E2 is indicated?

The electronic unit is too hot. Check the installation of the hob.

Make sure that there is sufficient ventilation.

See the section on thermal cut-off.

Error code U400 is indicated?

The hob has been incorrectly connected. The controls will switch

off after 1 s and a continuous signal will sound. Connect the

appliance to the appropriate power supply.

An error code (ERxx or Ex) is indicated?

The appliance has developed a technical defect. Please call

Customer service.

The pot sign appears ?

A cooking zone has been switched on and the hob is expecting a

suitable pot or pan to be placed on the cooking zone (pan

recognition). Only when a pot has been placed on the cooking

zone will power be supplied.

The pot sign still appears, even though a pot or pan was

placed on the hob?

The cookware is unsuitable for induction cooking or the pot or

pan is too small.

Is the cookware you are using making noises?

This is due to technical reasons; the induction hob and the pot

are not at risk.

Does the cooling fan still operate after it has been switched

off?

This is normal since the electronic unit is being cooled down.

Is the hob making noises (clicking or cracking sounds)?

This is for technical reasons and cannot be avoided.

Does the hob have tears or cracks?

If cracks, fractures or any other defects appear in your glass

ceramic hob, immediately switch off the appliance. Disconnect

fuse immediately and call Customer Service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Smeg SE 2931 ID Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Smeg SE 2931 ID

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info