Bedienungsanleitung Smeg SO6303 (Seite 57 von 66) (Englisch)

791162

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

CLEANING AND MAINTENANCE - 12991477A081/B

Preliminary operations

In case there is residual water inside the

reservoir:

1. Open the door.

2. Place a jug or a container on the open

door.

3. Pull the loading nozzle out of its housing.

4. Press the START button to start draining

the water into the jug (or container).

Residual water begins to drain into the jug (or

container).

5. Wait for the end of the drain flow.

6. Empty the water in the jug (or container).

7. Touch the CONFIRM button to

continue the function.

Reservoir filling

1. Mix 100 g of citric acid with 650 ml of

water in a jug.

2. Pull the loading nozzle out of its housing.

3. Place the end of the tube at the bottom of

the jug (or container).

4. Touch the START button to start filling

the reservoir of the appliance with the

descaling solution.

5. In the end, shake the loading nozzle to

remove any remaining water.

6. Place the loading nozzle place in its

housing.

7. Remove the jug (or container).

Boiler descaling function

1. Close the door

2. Descaling starts.

At the end of the descaling process the display

shows the request to drain the water softener.

Reservoir draining

1. Open the door

2. Place a jug or a container on the open

door.

3. Pull the loading nozzle out of its housing.

4. Press the START button to start draining

the water softener into the jug (or container).

The descaling solution begins to flow into the

jug.

5. Wait for the end of the drain flow.

6. Empty the descaling solution in the jug (or

container).

Cleaning the reservoir and hydraulic circuit

Once the water softener has been drained, the

appliance starts the cleaning procedure for the

reservoir and the hydraulic circuit.

The display will show the request to fill the

reservoir with water.

1. Fill a jug or container with about 2 litres of

clean water.

2. Open the oven door.

3. Place the jug (or container) on the open

door.

4. Pull the loading nozzle out of its housing.

5. Place the end of the tube at the bottom of

the jug (or container).

6. Press the START button to start filling the

appliance reservoir with water.

7. When you have finished filling water into the

reservoir, touch the CONFIRM button

to continue with the function.

The appliance starts the function using the

parameters set.

• When cleaning the tank and the hydraulic

circuit, leave the jug on the door open with

the filling nozzle inside. The appliance

cyclically discharges certain quantities of

water used for cleaning.

• During this process, the overflowing of water

inside the oven cavity is not intended as a

malfunction, rather it is part of the rinsing

From now on, it will no longer be

possible to cancel the descaling

process.

Do not use lactic acid or other

descaling agents.

Take care: the descaling solution may

be still hot.

Use cold tap water which is not too

hard, softened water or still mineral

water.

Do not use distilled water, tap water

with a high chloride content (> 40 mg/

l), or other liquids.

The overflowing of water inside the

oven cavity is not intended as a

malfunction, rather it is part of the rinsing

procedure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Smeg SO6303 Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info