Bedienungsanleitung Snom M200 SC Base Station (Seite 21 von 120) (Englisch)

809886

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

v1.01

M200SC Administrator and Provisioning Manual Conﬁguration using the Web user interface (WebUI)

Feature Synchronization Enables the M200SC to synchronize with Broadworks Application Server.

Changes to features such as DND, Call Forward All, Call Forward No An-

swer, and Call Forward Busy on the server side will also update the set-

tings on the handset menu and WebUI. Similarly, changes made using the

handset or WebUI will update the settings on the server.

DTMF method Select the default DTMF transmission method. You may need to adjust this

if call quality problems are triggering unwanted DTMF tones or you have

problems sending DTMF tones in general.

Unregister after reboot Enables the phone to unregister the account(s) after rebooting-before

the account(s) register again as the phone starts up. If other phones

that share the same account(s) unregister unexpectedly in tandem

with the rebooting M200SC, disable this setting.

Call Rejection Response

Code

Select the response code for call rejection. This code applies to the

following call rejection cases:

◦ User presses Reject for an incoming call (except when Call

Forward Busy is enabled)

◦DND is enabled

◦ Phone rejects a second incoming call with Call Waiting disabled

◦ Phone rejects an anonymous call with Anonymous Call Rejection

enabled

◦Phone rejects call when the maximum number of calls is reached

Dial Plan

The dial plan consists of a series of dialing rules, or strings, that determine whether what the user has dialed is

valid and when the handset should dial the number.

Note: Numbers that are dialed when forwarding a call (when the user manually fowards

a call, or when a

pre-conﬁgured number is dialed for Call Forward All, Call Forward on No Answer, or Call Forward Busy)

always bypass the dial plan.

Dialing rules must consist of the elements deﬁned in the table below.

Element Description

Any dial pad key from 0 to 9, including # and *.

[0-9] Any two numbers separated by a hyphen, where the second number is greater than the ﬁrst.

All numbers within the range or valid, excluding # and *.

x+ An unlimited series of digits.

This represents the playing of a secondary dial tone after the user enters the digit(s) speci-

ﬁed or dials an external call preﬁx before the comma. For instance, “9,xxxxxxx” means the

secondary dial tone is played after the user dials 9 until any new digit is entered. “9,3xxxxxx”

means only when the digit 3 is hit would the secondary dial tone stop playing.

PX This represents a pause of a deﬁned time; X is the pause duration in seconds. For instance,

“P3” would represent pause duration of 3 seconds. When “P” only is used, the pause time is

the same as the Inter Digit Timeout (see "General Account Settings" on page 20).

(0:9) This is a substitution rule where the ﬁrst number is replaced by the second. For example,

“(4:723)xxxx” would replace “46789” with “723-6789”. If the substituted number (the ﬁrst

number) is empty, the second number is added to the number dialed. For example, in “(:1)

xxxxxxxxxx”, the digit 1 is appended to any 10-digit number dialed.

This separator is used to indicate the start of a new pattern. Can be used to add multiple dial-

ing rules to one pattern edit box.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snom M200 SC Base Station Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info