Bedienungsanleitung Snom M200SC (Seite 60 von 68) (Englisch)

809888

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

v1.03

M215SC User Manual Appendix 1 - Base Station Settings

- The table always displays the maximum six accounts, even if there are fewer SIP accounts enabled.

- If you have not entered any unique handset names yet, then the default name of "HANDSET"

appears.

- On the Account Assignments table, you can select which accounts will be available for both

incoming and outgoing calls on each handset.

- The handset will rst attempt to use the account you select under Default when going o-hook.

◦Handset Name.

- On the Handset Name page, you can enter a name for each handset. The handset name will be used

throughout the web user interface and will appear on the handset's idle screen.

- The handset name is limited to a maximum of 11 characters.

- The default name is "HANDSET". Blank name elds are not allowed. If you click Save when any

elds are empty, an error message appears.

Network Settings

Basic Network Settings

Basic Network Settings Description

DHCP DHCP is selected (enabled) by default, which means the phone will get its IP address,

Subnet Mask, Gateway, and DNS Server(s) from the network. When DHCP is disabled,

you must enter a static IP address for the phone, as well as addresses for the Subnet

Mask, Gateway, and DNS Server(s).

Static IP When Static IP is selected, you must enter a static IP address for the phone, as well as

addresses for the Subnet Mask, Gateway, and DNS Server(s).

IP Address If DHCP is disabled, enter a static IP address for the phone.

Subnet Mask Enter the subnet mask.

Gateway Enter the address of the default gateway (in this case, your router).

Primary DNS If DHCP is disabled, enter addresses for the primary and secondary DNS servers.

Secondary DNS

Advanced Network Settings

VLAN Settings Description

Enable LAN Port VLAN Enable if the phone is part of a VLAN on your network. Select to enable.

VID Enter the VLAN ID (vlan 5, for example).

Priority Select the VLAN priority that matches the Quality of Service (QOS) settings that you

have set for that VLAN ID. Outbound SIP packets will be marked and sent according to

their priority. 7 is the highest priority.

LLPD-MED Settings Description

Enable LLDP-MED Enables or disables Link Layer Discovery Protocol for Media Endpoint Devices

(LLDP-MED). LLDP-MED is a standards-based discovery protocol supported on some

network switches. It is required for auto-conguration with VLAN settings.

Packet Interval (secs) Sets the LLDP-MED packet interval (in seconds).

802.1x Settings Description

Enable 802.1x Enables or disables the 802.1x authentication protocol. This protocol allows the

phone to attach itself to network equipment that requires device authentication via

802.1x.

Identity Enter the 802.1x EAPOL identity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snom M200SC Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Snom M200SC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info