Bedienungsanleitung Snom M400 (Seite 70 von 76) (Englisch)

809890

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

v1.01

Admin and Installation Guide M400 Description of Settings

Setting Description

System (Fig. 1 and 2)

Base station name In multicell setup: IP address and - if set - name assigned to base station in

Management settings

Operation/duration D-H:M:S Operation: Time since last reboot ((days–hours:minutes:seconds)

Duration

DECT operation D-H:M:S How long the base station has been running (days–hours:minutes:seconds)

Busy The number of times the base station has been busy

Busy duration The total time the base station has been busy for speech (8 or more calls

active)

SIP failed The number of times SIP registrations have failed

Handset removed The number of times handsets have been marked as removed

Searching The number of times the base station has searched for its sync source

Free Running The number of times the base station has been free-running

DECT source changed The number of times the base station has changed its sync source

Calls (Fig. 3)

Base station name In multicell setup: IP address and - if set - name assigned to base station in

Management settings

Operation duration Operation: Time since last reboot



Count Number of calls on base station

Dropped Number of active calls that were dropped for reasons like handset moving out

of range etc. An entry is stored in the syslog.

No response Number of active calls that weren't answered, for example because handset

was out of range etc. An entry is stored in the syslog.

Duration The total time that calls were active on the base station.

Active The total number of active calls on the base station (DECT and non-DECT

calls). There can be up to 8 calls on a base station in a multicell installation,

and up to 10 active calls on a single-cell base station.

Max active The maximum number of calls that have been active at the same time.

Codec Logging and count of codecs used on each call.

Handover success The number of successfull handovers

Handover failed The number of failed handovers

Audio not detected Number of incidents

Repeater (Fig. 4)

Idx/name Idx and - if set - name assigned to repeater in Repeaters settings

Operation Total operation time since last reboot or reset.

Busy The number of times the repeater was busy.

Busy duration The total time that the repeater was been busy for speech (5 or more calls

active).

Max active The maximum number of calls that have been active at the same time.

Searching The number of times the repeater has searched for its sync source.

Recovery When the repeater has lost its sync source, it will attempt to lock onto another

base station or repeater. Statistics show recovery mode.

DECT source changed The number of times the repeater has changed its sync source.

Wideband The number of wideband calls on repeaters

Narrowband The number of narrowband calls on repeaters

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snom M400 Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info