809892
53
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
53
v1.05
Admin and Installation Guide M900 Description of Settings
Setting Description
ID 12-bit identication of the 802.1Q VLAN. Permitted value(s): Decimals 0 to
4094. A VLAN ID of 0 is used to identify priority frames and the ID of 4095
(i.e., FFF) is reserved. If 0 is set, there is no VLAN tagging or VLAN discovery
through DHCP.
Default: 0.
User priority 3-bit value dening user priority. Values are 0 (best eort) and 1 to 7 (lowest
to highest priority). The values can be used to prioritize dierent classes of
trac (voice, video, data, etc.).
Default: 0
Synchronization If enabled, the VLAN ID is automatically synchronized between the base
stations in a multicell chain. They will be automatically rebooted during the
synchronization.
Default: Disabled.
Send LLDP-MED message TBA
Default: Disabled.
Try obtaining VLAN via LLDP-
MED
TBA
Default: Disabled.
DHCP Options
Plug-n-play If enabled: DHCP option 66 is used to automatically provide PBX IP address to
base station.
Default: Disabled.
TCP Options
TCP keep alive interval Default: 120s. The time (in seconds) between individual keepalive probes.
NAT Settings
Enable STUN Default: Disabled. Enable to use STUN.
STUN server Permitted value(s): IPv4 values or URL. Currently only IPv4 is supported.
STUN bindtime determine Default: Disabled.
STUN bindtime guard Time in seconds. Permitted values: Positive integers.
Default: 80.
Enable RPORT Default: Disabled. Enable to use RPORT in SIP messages.
Keep alive time The interval in seconds at which the base station sends a keepalive signal to
the SIP server to maintain NAT bindings. Permitted values: Positive integers.
Default: 90.
SIP/RTP Settings
Use dierent SIP ports If disabled, the local SIP port parameter species the source port used for SIP
signaling in the system.
If enabled, the local SIP port parameter species the source port used for rst
user agent (UA) instance. Succeeding UAs will get succeeding ports.
Default: Disabled.
RTP collision detection Enabled: If two sources have the same SSRC identier, the second RTP is
discarded.
Disabled: SSRC identiers are not checked; device accepts all sources.
Default: Enabled.
Always reboot on checksync Enable to reboot base station whenever new conguration is loaded.
Default: Disabled.
Outbound proxy mode Use Always: All outbound calls are sent to outbound proxy.
Only Initial request: Use outbound proxy for initial SIP requests only.
Default: Use Always
Failover SIP timer B TBA
Failover SIP timer F TBA
53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Snom M900 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Snom M900

Snom M900 Bedienungsanleitung - Deutsch - 79 seiten

Snom M900 Bedienungsanleitung - Englisch - 44 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info