Bedienungsanleitung Snom M900 (Seite 70 von 80) (Englisch)

809892

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

v1.05

Admin and Installation Guide M900 Description of Settings

Setting Description

System combination (number

of base stations/repeaters

per base station)

Three settings are available.

Note: The conguration must be set at the time the multicell system is

congurated. It cannot be modied:

50/3: 50 base stations and 3 repeaters

127/1: 127 base stations and 1 repeater

254/0: 254 base stations and 0 repeater

Base Station Group (Fig. 2)

ID Base station identity in the chained network. Automatically assigned

consecutively when new base stations are added to the chain. With checkbox

for selection for removal from chain.

Permitted output: Positive integers.

RPN The Radio Fixed Part Number is an 8-bit DECT cell identity allocated by the

installer. The allocated RPN within the SME must be geographically unique.

Permitted output: 0 to 255 (DEC) or 0x00 to 0xFF (HEX)

Version Current rmware version on base station.

Permitted output: Positive integers with dot (e.g, 355.21).

MAC address The media access control (MAC) address is a unique identier assigned by the

manufacturer. Printed on device's label and on Home page of web interface.

IP address The Internet Protocol address assigned by the network the base station is

located in.

IP status Current base station status in the SME network.

This unit: Indicates that you are looking at this base station's web interface.

Connected: The base station is online in the network.

Connection lost: The connection to the base station has been lost.

DECT sync source The drop-down menu contains the RPNs of each of the currently connected

base stations followed (in parentheses) by the strength of the respective radio

signal (RSSI) in dBm, as received by the base station whose web interface you

are currently accessing. The maximum number of multicell chain levels is 24.

• When the DECT system setting Auto congure DECT sync source tree is

set to "enabled", the sync source tree will be generated automatically.

• When the setting is "disabled", the sync source tree must be congured

manually by selecting each base station's sync source from the drop-

down menu.

The visible option shows which sync source each of the base stations in the

DECT chain is currently using. If you select a dierent option, the chain must

be rebooted. Options:

Select as primary: This option is visible when the base station is selected

as the primary. Select from the drop-down menu of a secondary base

station to make that base station the primary.

Primar y:RPNxx (-xxdBm): This option is visible when the base station is

a secondary level base station whose sync source is the primary.

Example: Primary:RPN00 (-72dBm)

Levelx: RPNxx (-xxdBm): This option is visible when the base station is a

secondary level base station whose sync source is another secondary

level base station.

Example: Level1:RPN04 (-68dBm)

(any) R PN: Indicates a base station that is not synchronized to any other base

station.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snom M900 Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Snom M900

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info