Bedienungsanleitung Snooper S7000 - VenturaXL PRO (Seite 11 von 87) (Englisch)

588711

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

11 • UK

Return to contents

Installing S7000

S7000 comes with a windscreen bracket so that the unit can be mounted onto your vehicles windscreen.

When installing S7000 please ensure that:

● The unit, with its built in GPS antenna has a clear view of the sky*

● It is located in a position where you can easily view the LCD display without having to take your eyes too far from the road ahead

and that you can reach the controls safely.

● Does not interfere with the vehicles controls

● Does not jeopardise the drivers or passengers safety

● You will be able to remove the device to perform downloads.

*Please Note: Some vehicles including Renault, Citroen and Peugeot may come with a ‘Heat Reﬂective’, ‘Metal Oxide’, ‘Athermic’ or

‘Comfort’ windscreen which may aﬀect the performance of the built in GPS antenna. If you are unsure what type of windscreen is

ﬁtted to your vehicle then contact your local vehicle dealer or manufacturer for further information. In these situations you will need

to purchase an extension GPS antenna, which can be positioned either on the rear parcel shelf or outside the cabin of the vehicle.

Call 0333 240 1000 and select Option 1 for further details.

PLEASE NOTE: Be careful to choose a location that does not block the drivers view or where it might endanger the driver or

passengers should your vehicle suddenly come to a stop or be involved in an accident.

Installing S7000 using the Windscreen Suction Cup bracket

You can mount S7000 to the inside of your vehicles windscreen using the

windscreen bracket provided.

● Clean the area where you wish to position the bracket thoroughly with a good

quality glass cleaner. This allows a more secure seal on the windscreen.

● Place the suction cup and bracket on the windscreen and push the locking

lever towards the windscreen to secure the bracket.

● Adjust the angle of the bracket so that when the unit is attached to it you can

view the display and operate the controls safely.

● Position S7000 onto the bracket, by placing it onto it as indicated and click into

place . Remove S7000 by pressing the lever down and then removing the S7000.

● S7000 can be powered directly either from the internal battery if it is fully

charged or powered from the cigarette lighter socket. To use the cigarette lighter

socket, plug the smaller plug on one end of the power cable into the power

socket marked on the right hand side of S7000 and plug the larger plug into the

cigarette lighter socket of your vehicle.

Please Note: Only use the cigarette lighter power cable provided with S7000. S7000 operates on 9V and using any other

cigarette lighter power cable will damage your device and void the warranty.

Locking

lever

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snooper S7000 - VenturaXL PRO Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Snooper S7000 - VenturaXL PRO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info